Immergas EOLO Star 23 kW Technical Documentation Manual Download Page 6

Page: 6 / 32

STESkW ed 05/06

EOLO Star 23 kW

Technical Documentation

The central heating circuit, with relevant control and safety

devices, is operated

every time a central heating request is

made

Operation.

The heat contained in the fumes produced by combustion

is absorbed by the copper blades of the water-gas exchanger

(7) which, in turn, transfers it to the water circulating inside

thanks to the boiler circulator (16).

The hot water is then transferred directly into the central heat-

ing system through the delivery (M) and return (R) pipes.

Legend:

1 - D.h.w. probe

2 - D.h.w. ﬂow switch

3 - Gas valve

4 - Flow limiter

5 - Draining cock

6 - Burner

7 - Rapid exchanger

8 - Fan

9 - Sealed chamber

10 - Flue pressure switch

11 - Draught diverter

12 - System expansion vessel

13 - Delivery probe

14 - Safety thermostat

15 - Automatic air vent

16 - Boiler circulator

17 - System pressure switch

18 - Automatic by-pass

19 - 3 bar safety valve

20 - Filling valve

G - Gas supply

AC - D.h.w. outlet

AF - Cold water inlet

R - System return

M - System delivery

Hydraulic circuit.

Primary circuit (Boiler Circuit).

Hot water for central heating and domestic use is produced

by two separate circuits that work as required.

http://serviceimmergas.ro

Summary of Contents for EOLO Star 23 kW

































Search results

Summary of Contents for EOLO Star 23 kW

Reviews:

Related manuals for EOLO Star 23 kW

Brands by name

Popular brands

Immergas EOLO Star 23 kW, Technical Documentation Manual

Search results

Summary of Contents for EOLO Star 23 kW

Reviews:

Related manuals for EOLO Star 23 kW

Brands by name

Popular brands