background image

27

STESkW ed 05/06 

EOLO Star 23 kW

Technical Documentation

Technical Documentation

  EOLO Star 23 kW operating sequence

 

Central heating phase 

Domestic hot water phase

Power on

Boiler functioning button on Winter

Enabling integrated board operation

Closing of the functioning button contacts 

(Winter position)

 

enables operation in the central heating mode

Closing of the Room thermostat/ CRD operation request

Either the room thermostat or CRD 

(if installed)

 detects the 

conditions that require operation in the central heating mode

Power on

Boiler functioning button on Summer or Winter

Enabling integrated board operation

Closing of the functioning button contacts 

(Summer position)

 

enables operation in the d.h.w. mode

Closing the d.h.w. flow switch

Drawing domestic hot water

Powering the pump

With the system pressure switch enable, the modulation board 

powers the pump

 

Ú

 

Ú

 

Ú

 

Ú

 

Ú

 

Ú

 

Ú

 

Ú

Turning the pump off

The pump is not switched on or is turned off if there is an 

ongoing central heating request

Flue pressure switch contact control

The integrated board verifies switching of the flue pressure switch contact as a result of the fan working 

(normally open contact NO)

Flue pressure switch contact control

The integrated board verifies the correct position of the flue pressure switch 

(normally closed contact, NC)

Closing the system pressure micro switch

When pressure in the primary circuit is higher than the minimum cutoff value, it causes closure of the system pressure switch contact

Ú

Ú

Ú

Powering the gas valve coils

With the enable of the overtemperature safety thermostat the integrated board powers the gas valve coils

Ú

Burner ignition 

(automatic soft ignition)

The integrated board sends the soft ignition current to the modulation coil

Flame detection

By means of the ionisation electrode, the integrated board detects burner ignition

Powering the ignition electrode

The integrated board powers the ignition electrode

Ú

Ú

Boiler working

The burner works at a power that varies according to the type of request, to the adjustments/settings made and to the temperatures 

detected by the NTC probes

Ú

Ú

Powering the fan

The integrated board powers the fan

                                         http://serviceimmergas.ro

Summary of Contents for EOLO Star 23 kW

































Reviews: