4.1 Addressing
If more than one unit is connected to the LED-8C,
addresses may be assigned to the units to obtain run-
ning light effects in the colour switching mode 2.
4.1.1 Automatic addressing
This method is useful for addressing the units con-
nected in the chain in groups of 4 or 8.
Example:
20 units connected
Fig. 3 Addressing in groups of 4
Fig. 4 Addressing in groups of 8
1) Select the group mode with the switch CHASER
CHANNEL MODE (14):
position 4CH = groups of 4
position 8CH = groups of 8
2) Connect all units with each other and switch them
on.
3) Keep the button BLACKOUT (10) pressed for 5
seconds until the LED above the button flashes.
The addressing mode is switched on and the LEDs
of the first unit in the chain light up.
4) Press the button SOUND TO CHASE (8). The LEDs
of all units connected light up.
5) Press the button WHITE / RANDOM (1). The yellow
LED above the button lights up.
6) To switch off the addressing mode, keep the button
BLACKOUT pressed again for 5 seconds so that
the red LED of the button does not flash any more
and all LEDs of the units connected extinguish.
4.1.2 Manual addressing
For manual addressing, an address from 1 to 8 can be
assigned to each unit.
1) With the switch CHASER CHANNEL MODE (14)
select if a maximum of 4 addresses (4CH) or
8 addresses (8CH) should be allocated.
2) Connect all units with each other and switch them
on.
3) Keep the button BLACKOUT (10) pressed for
5 seconds until the LED above the button flashes.
The addressing mode is switched on. The first unit
in the chain is selected: The LEDs of the unit light
up.
4) Adjust the desired address for the selected unit with
the buttons CHASE 1 to CHASE 8 (1).
5) Select the next unit in the chain with the button
FULL ON/NEXT PROJECTOR (9). With the button
SOUND TO CHASE / PREVIOUS PROJECTOR (8)
it is possible to switch back to the previous unit.
6) For addressing all further units, repeat the steps 4
and 5 in each case. Adjust the same address for
units to be controlled in sync.
7) To switch off the addressing mode, keep the button
BLACKOUT pressed again for 5 seconds so that
the red LED of the button does not flash any more
and all LEDs of the units connected extinguish.
4.2 Brightness of the LEDs /
stroboscope function
After switching on the control panel the function Black-
out is activated: The units connected are turned off; the
red LED above the button BLACKOUT (10) lights up.
1) For switching the units to brightness, press the but-
ton BLACKOUT so that the LED above the button
extinguishes.
2) Adjust the desired brightness with the control MAS-
TER (7).
3) To switch on the stroboscope function, set the con-
trol MASTER to the upper adjusting range. Here the
flash frequency can be adjusted from slow ( ) to
fast (
). If the control is set to the upper stop, the
stroboscope function is switched off and all LEDs
light at maximum brightness.
4) With the button BLACKOUT the units can be turned
off and switched to brightness again. As long as the
units are dark, the red LED above the button
BLACKOUT lights up as a check.
5) All LEDs of the units can be switched to maximum
brightness at any time (white light). For this purpose
keep the button FULL ON (9) pressed.
4.3 Fixed colour mode
This mode is activated after switching on or pressing
the button HOLD COLOURS (2). It is possible to select
9 preset colours with the buttons HOLD COLOURS –
CHASE (1).
LED-8C
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
LED-8C
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
10
GB
