imex Bullseye 80 User Manual Download Page 16

Page: 16 / 20

Press

to confirm the result.

Press

to cancel the result. Press twice to exit without saving.

Message codes

All message codes are displayed with either “Info” or “Error”.

Info

Cause

Remedy

204

Calculation overflow

Repeat procedure

252

Temperature too high

Cool down instrument

253

Temperature too low

Warm up instrument

255

Receiver signal too weak

Use target plate

256

Received signal too strong

Use target plate (grey side)

205

Ranging transfinite

Use in allowed ranging

206

Wrong parameter

When measuring by Pythagoras, the
length of hypotenuse should be greater
than the other two lengths
The parameter calculated must have the
same unit

156

Transverse tilt greater than

10°

Hold the instrument without any
transverse tilt

Error

Cause

Remedy

Err

Hardware error

Switch  on/off  the  device  several
times  and  check  if  the  symbol
still  appears.  If  so  please  call
your dealer for assistance

Summary of Contents for Bullseye 80





















Search results

Summary of Contents for Bullseye 80

Reviews:

Related manuals for Bullseye 80

Brands by name

Popular brands

imex Bullseye 80, User Manual

Search results

Summary of Contents for Bullseye 80

Reviews:

Related manuals for Bullseye 80

Brands by name

Popular brands