background image

Dseries Harris J/S (JSC-2) Jog-Shuttle Control Panel  
Reference 

 

About this Manual 

 

About this Manual 

Audience 

This manual is intended as a general reference and for use by engineers or 
technicians when installing professional automation computers. 

Measurement Standards 

The following measurement standards are used in this manual: 

 

Rack Unit (RU) is an Imperial standard measurement for device height. (While 
also seen as U.) [1RU = 44.45mm = 1.75 inches]  

 

19” Rack Standard is an international standard for racking width. [19” Rackmount 
standard = 482.6mm] 

 

Other measures for in-document conversion: (1m = 3.281ft), (0.3048m = 1ft), 
(25.4mm = 1in), (1kg = 2.205lb) 

 

Website for length & weight conversions: http://www.convert-me.com/en/convert  

Product Unpacking Notes 

Thoroughly inspect all articles immediately upon receipt. Any damage discovered 
should be cause for a damage claim against the carrier.  

WEEE and RoHS Compliance 

Panels addressed in this document are WEEE and RoHS Compliant. This includes 
compliance with Electrical and Electronic Equipment (WEEE) and Restriction on 
Hazardous Substances (RoHS) (Combined WEEE/RoHS) requirements now 
mandated in Europe, and being adopted in other parts of the world. 

Restriction of Hazardous Substances Directive (RoHS) 2002/95/EC

 

mandates: Recycling of devices at end of life and the elimination or reduction 
of a list of hazardous substances. This includes six key hazardous materials 
typically used in the manufacture of various types of electronic and electrical 
equipment: Lead, Mercury, Cadmium, Hexavalent chromium (chromium VI or 
Cr6+), Polybrominated biphenyls (PBB), and Polybrominated diphenyl ether 
(PBDE) 

 

© 2014 Imagine Communications Corp.     Proprietary and Confidential 

 9-April-2014  | Page 5 of 21 

Summary of Contents for 502072-00






















Reviews: