background image

Dseries Harris J/S (JSC-2) Jog-Shuttle Control Panel  
Reference 

 

Operation 

 

Button    
Description 

Previous 
Keycap 
Engraving 

DALstation Functionality 

Fifth Button, 
Third Row

 

 

If one of the following contexts is applicable, ‘Stop’ 
is commanded. 

1.  Ad Hoc Ingest Window is open (Source or 

Destination assigned) 

2.  Record bus is displayed (Destination 

assigned) 

3.  VCP Window is active (Source assigned) 

Reconfigurable

? No. 

Second 
(CW) Button 
Surrounding 
Knob 

MARK 
SOM 

1.  Copy current timecode from destination 

machine into on-air event’s bus SOM field 
with Ad Hoc Ingest Window open (Destination 
assigned) or Record bus displayed 
(Destination assigned). In addition, 

 

If the ‘Use first bus item’ is set to ‘Y’ in 
BUS.TBL, the SOM of the item for each 
bus machine will be set to the current 
timecode of the assigned destination 
machine,  

 

If the ‘Use first bus item’ field in BUS.TBL 
is either blank or set to ‘N’, the SOM of 
the item for only the assigned destination 
machine will be set to the current 
timecode reported by that bus or bus 
monitor machine. Since all other 
machines are unaffected, the Mark SOM 
command needs to be performed once for 
each bus machine. 

2.  If the Ad Hoc Ingest Window is active (Source 

Assigned) and the source assignment is from 
the schedule, the SOM of the source machine 
is written to the sub-event field.  

3.  If the VCP Window is active (Source 

Assigned) and displays a valid timecode, the 
current timecode is copied from the VCP 
Window timecode display to the VCP Window 
SOM field (Note: Bus display does not reflect 
SOM change until ‘Set Event Data’ button is 
selected from VCP Window). 

* See additional note following this table. 

Reconfigurable

? No. 

Third (CW) 
Button 
Surrounding 
Knob 

GO TO 
SOM 

If one of the following contexts is applicable, ‘Go 
to Start of Material’ is commanded. 

1.  Ad Hoc Ingest Window is open (Source or 

Destination assigned)  

2.  Record bus is displayed (Destination 

assigned) 

3.  VCP Window is active (Source assigned) 

Reconfigurable

? No. 

 

© 2014 Imagine Communications Corp.     Proprietary and Confidential 

 9-April-2014  | Page 13 of 21 

Summary of Contents for 502072-00






















Reviews: