manualshive.com logo in svg

Image Engineering lightSTUDIO, User Manual, Page: 18 / 21

Share
Download
Image Engineering lightSTUDIO User Manual Download Page 18

 

  Software Documentation 

 

 

 

 

Image Engineering   

lightSTUDIO  

18 

4.5.3.3

 

HDR

 BOX

 

 

 

The HDR (High Dynamic Range) module in the software enables you to control both LG2 lamps of the 

HDR box. The upper lamp is switched on with button [1] and the intensity controlled with a slider or an 

input field [2]. The same applies to the lower lamp, buttons [3] and [4].  

For both lamps separate sequence lists are available. Activating the sequence or looping functionality 

(

chapter 

Fehler! Verweisquelle konnte nicht gefunden werden.

) applies for both lamps. Enter start 

and end times as well as the intensity from 0

…

100 %. 

Take into account that switching the LG2 on and off lamps takes 1

…

2 s, thus shorter periods are not 

advisable and may be omitted in the sequence player. 

 

4.5.4 T

IMECODE 

D

ISPLAY

 

              

  

 

The module for the timecode display (

chapter 2.2

) offers two operating modes: timer and counter. 

Switch between the modes with menu [1]. 

Timer mode

: 

Start and stop the timecode with the 

start/stop

 button [2].  

Clicking the reset button [3] resets the timecode display to 00:00.000.  

Summary of Contents for lightSTUDIO






















Reviews:

No comments