background image

24

IMPORTANT SAFETY WARNINGS

The installation and extraordinary maintenance operations 
must be carried out by qualified personnel, authorized by 
the Manufacturer, having the necessary product 
knowledge, and in compliance with the regulations in 
force in the Country of use regarding the types of systems 
involved and safety in the workplace.
Before connecting the device to the mains, please check 
that all connection data on the product label (voltage 
and frequency) match those of the mains (Refer to 
chapter “How to read product label” on page 27 for 
further information on the data plate). Please note that 
any  incompatibility could lead to serious damage to the 
device, so always contact a qualified electrician before 
installing your hood; check that the systems comply with 
the  regulations in force in the Country of use; always 
compare the system data with that printed on the data 
plate;
check all the components for integrity and functionality: in 
case of fault, stop the installation and contact the 
distributor.
Do no connect the product to the power main before any 
other step of the installation is completed;
Any interventions, tampering or modifications not  
expressly  authorised,  not  complying  with  the  content  of 
this manual, will void the warranty, and may also cause 
immediate danger or dangerous situations that may 
result in injury or even death.
During the installation of the equipment, anyone not 
responsible for carrying out installation
activities must refrain from transiting or stationing in or 
nearby the installation area.
Being potentially hazardous, packaging materials must 
be kept out of reach of children or animals, and must be 
correctly disposed of, in accordance with local 
regulations.
During the installation activities, always use the required 
personal protective equipment (e.g. safety shoes) and 
act with the due level of care and attention.

Summary of Contents for IAG

































Reviews: