Ilex Filtration Biodrum 20 +31384447366
6
Subject to typesetting and printing errors
4.
Use of the drum filter
Only use the filter when no body parts are in
contact with the water! Before you reach into the
water, always disconnect the filter from the power
supply. Compare the electrical specification on the
type label of the device with the specification of
the power supply. Make sure that the device is
connected to an ELCB (earth leakage circuit
breaker) with an assigned leakage rating of max.
30 mA (DIN VDE 0100T739). Only operate the
device on a correctly installed power plug.
Keep the power plug and the wiring dry! Make
sure that the cables are protected to prevent
damage and consequent short circuits.
THE WIRING OR THE POWER PLUGS MUST
NOT BE CUT. DOING SO WILL IMMEDIATELY
INVALIDATE ALL WARRANTY AND LIABILITY
OF THE MANUFACTURER.
Only use wiring, installations, adapters, extension
cables and connection cables with grounding-type
plugs, which are approved for outdoor usage (DIN
VDE 0620) with sufficient cable diameter. Do not
pull on the wiring of the devices or use the wiring
to carry the devices! If a wiring is damaged or
broken, the device may no longer be used! Take
care that power plugs never falls into water or
gets wet. If a plug gets wet,
it must be opened by a professional and cleaned
by purging with demineralised water. Protect
plugs and the wiring from heat, oil, UV light and
sharp corners. The manufacturer is not liable in
any way for any damage caused by improper
installation or by the carelessness of the user or
installer.
The wiring may not be modified or replaced.
Electrical installations on garden ponds must
always comply with national and international
directives and requirements. Never open the case
of the device(s) or of the appending parts if this is
not explicitly suggested in the user manual. Never
apply technical modifications of the device(s).
Only use original spare parts and accessories.
Only allow authorised customer service facilities to
conduct repairs. Never use the filter with any
other liquids than water.
5.
Fields of application
The Drum filter is suitable for freshwater and
brackish water.
Temperature of the water: +4 to +40 °C.
Environment temperature: +2 to +50 °C
Protection class control box: IP54.
6.
Installation/Fitting
CAUTION:
Before you install the filter, read the manual
carefully. Damage caused because the manual
was not read thoroughly does not fall under
warranty.
When unpacking the filter, check if all parts have been
delivered completely and undamaged. Any damage
detected must be reported to your retailer within 24
hours of purchasing the filter. Please check the device
for damage before you operate it. Do not use the
device if it is damaged. Please inform your retailer
immediately. If the device is used despite being
damaged, any warranty and liability will then be
invalid.
During the course of the installation, the device may
not be connected to the power supply. Remove all
plugs from the electric sockets and make sure that
the filter cannot be switched on. To avoid injury,
make sure that your hands or fingers cannot reach
the rotating parts of the filter when it is connected to
the power supply.
7.
Operating the filter
NEVER USE THE DEVICE WITHOUT
WATER THROUGHPUT.
7.1
Placing the filter
You must carefully follow the instructions below to
work safely and prevent damage to the equipment.
•
Ensure that the substrate is levelled and sufficiently
robust; the filter weighs more than 400 kg when
operational. A concrete slab is the preferred option.
•
When checking if the waste pump or drum motor is
still working, the lid must always be closed. Never
put your hands in the filter or try to stop the drum
with your hands.
•
The waste pump must always be below the water
level before it is switched on. If not, it will be
irreparably damaged because of running dry or
overheating. The warranty will not cover damage to
the waste pump because the pump has run dry.
•
The electronics must be suspended in a dry and
appropriately ventilated room. The temperature of
the room where the electronics is suspended must be
between 2 and 30 °C. If the temperatures are higher,
the electronics cannot handle its own heat properly
and this may lead to damage.
