DEUTSCH 22
Sicherstellen, dass der Deckel fest angeschraubt ist, so dass kein
Spülmittel während dem Waschprogramm in den Behälter gelangt
(dies könnte den Wasserenthärter irreparabel beschädigen).
Sobald dieses Verfahren abgeschlossen ist, ein Programm ohne
Beladung laufen lassen. Das „Vorspül“-Programm allein ist NICHT
AUSREICHEND. Übergelaufene Salzlösung bzw. Salzkörner können
zu Korrosion führen und den Edelstahlbehälter beschädigen.
Für Reklamationen in diesem Zusammenhang, kann von uns keine
Garantieleistung übernommen werden.
Verwenden Sie bitte nur Spezialsalz für Geschirrspüler.
Wenn der Salzbehälter nicht gefüllt ist, könnten
Kesselsteinablagerungen den Wasserenthärter und das
Heizelement beschädigen. Die Verwendung von Salz wird bei
jeder Art von Geschirrspülmittel empfohlen.
Immer wenn Sie Salz zugeben müssen, ist es zwingend
vorgeschrieben, diesen Vorgang vor dem Beginn des
Spülgangs auszuführen, um Korrosion zu vermeiden.
Wasserhärte einstellen
Damit der Wasserenthärter perfekt arbeiten kann, muss die
Wasserhärte je nach der aktuellen Wasserhärte in Ihrem Haus
eingestellt werden. Diese Information erhalten sie bei Ihrem
örtlichen Wasserversorger. Das Werk stellt den Standardwert für
die Wasserhärte ein.
• Gerät mit der EIN/AUS-Taste einschalten.
• Gerät mit der EIN/AUS-Taste ausschalten.
• Die Taste
• Switch on the appliance by pressing the ON/OFF button.
• Switch off the appliance by pressing the ON/OFF button.
• Hold down button
for 5 seconds, until you hear a beep.
• Switch on the appliance by pressing the ON/OFF button.
•
•
The current selection level number and the salt indicator light
� � � � � �
Press button
to select the desired hardness level (see
WATER HARDNESS TABLE).
• Switch off the appliance by pressing the ON/OFF button.
Setting is complete!
Water Hardness Table
Level
°dH
German degrees
°fH
French degrees
1
Soft
0 - 6
0 - 10
2
Medium
7 - 11
11 - 20
3
Average
12 - 17
21 - 30
4
Hard
18 - 34
31 - 60
5
Very hard
35 - 50
61 - 90
Make sure the cap is screwed on tightly, so that no detergent can
get into the container during the wash program (this could damage
the water softener beyond repair).
As soon as this procedure is complete, run a program without
loading. The “Pre-Wash” program alone is NOT� � � � � �
Residual saline solution or grains of salt can lead to corrosion,
irreparably damaging the stainless steel components.
The guarantee is not applicable if faults are caused by such
circumstances.
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
s.
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
heating element may be damaged as a result.
Whenever you need to add salt, it is mandatory to complete
the procedure before the beginning of the washing cycle.
SETTING THE WATER HARDNESS
To allow the water softener to work in a perfect way, it is essential
that the water hardness setting is based on the actual water hard-
ness in your house. This information can be obtained from your local
water supplier. The factory setting is for average (3) water hardness.
FILLING THE RINSE AID DISPENSER
A
should be filled when the
RINSE AID REFILL indicator light
B
(110 ml) reference notch of the filling space - avoid spilling it.
NEVER pour the rinse aid directly into the tub.
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satisfied with the drying results, you can
The current selection level number and rinse aid indicator light flash.
the dishwasher model. The factory setting is specific to the model,
FILLING THE DETERGENT DISPENSER
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
dishwashers.
useof detergent, rinse aid liquid and refined salt is required.
To open the detergent dispenser
press button A.
Introduce the detergent into
the dry dispenser B only.
Place the amount of detergent
for pre-washing directly inside
the tub.
A
B
B
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the TABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
5 Sekunden lang gedrückt halten, bis Sie einen
Piepton hören.
• Gerät mit der EIN/AUS-Taste einschalten.
• Die Nummer der aktuell ausgewählten Stufe und die
Salznachfüllanzeige blinken.
• Drücken Sie die Taste
• Switch on the appliance by pressing the ON/OFF button.
• Switch off the appliance by pressing the ON/OFF button.
• Hold down button
for 5 seconds, until you hear a beep.
• Switch on the appliance by pressing the ON/OFF button.
•
•
The current selection level number and the salt indicator light
� � � � � �
Press button
to select the desired hardness level (see
WATER HARDNESS TABLE).
• Switch off the appliance by pressing the ON/OFF button.
Setting is complete!
Water Hardness Table
Level
°dH
German degrees
°fH
French degrees
1
Soft
0 - 6
0 - 10
2
Medium
7 - 11
11 - 20
3
Average
12 - 17
21 - 30
4
Hard
18 - 34
31 - 60
5
Very hard
35 - 50
61 - 90
Make sure the cap is screwed on tightly, so that no detergent can
get into the container during the wash program (this could damage
the water softener beyond repair).
As soon as this procedure is complete, run a program without
loading. The “Pre-Wash” program alone is NOT� � � � � �
Residual saline solution or grains of salt can lead to corrosion,
irreparably damaging the stainless steel components.
The guarantee is not applicable if faults are caused by such
circumstances.
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
s.
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
heating element may be damaged as a result.
Whenever you need to add salt, it is mandatory to complete
the procedure before the beginning of the washing cycle.
SETTING THE WATER HARDNESS
To allow the water softener to work in a perfect way, it is essential
that the water hardness setting is based on the actual water hard-
ness in your house. This information can be obtained from your local
water supplier. The factory setting is for average (3) water hardness.
FILLING THE RINSE AID DISPENSER
A
should be filled when the
RINSE AID REFILL indicator light
B
(110 ml) reference notch of the filling space - avoid spilling it.
NEVER pour the rinse aid directly into the tub.
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satisfied with the drying results, you can
The current selection level number and rinse aid indicator light flash.
the dishwasher model. The factory setting is specific to the model,
FILLING THE DETERGENT DISPENSER
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
dishwashers.
useof detergent, rinse aid liquid and refined salt is required.
To open the detergent dispenser
press button A.
Introduce the detergent into
the dry dispenser B only.
Place the amount of detergent
for pre-washing directly inside
the tub.
A
B
B
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the TABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
um die gewünschte Härtestufe
auszuwählen (siehe WASSERHÄRTE-TABELLE).
• Gerät mit der EIN/AUS-Taste ausschalten. Die Einstellung ist
abgeschlossen!
Wasserhärte-Tabelle
Stufe
°dH
Deut.
Härtegr.
°fH
Französischer
Härtegr.
°Clark
Englische
Härtegr.
1
Weich
0 - 6
0 - 10
0 - 7
2
Mittel
7 - 11
11 - 20
8 - 14
3
Durchschnittlich
12 - 16
21 - 29
15 - 20
4
Hart
17 - 34
30 - 60
21 - 42
5
Sehr hart
35 - 50
61 - 90
43 - 62
Klarspülerspender auffüllen
Klarspüler macht das TROCKNEN von Geschirr einfacher.
Der Klarspülerspender A muss aufgefüllt werden, wenn das
KLARSPÜLER AUFFÜLLEN Anzeigelicht
1. Upper rack
2. � � � � � � �
3. Upper rack height adjuster
4. Upper sprayer arm
5. Lower rack
6. Cutlery basket
7. Lower sprayer arm
8. Filter Assembly
9. Salt reservoir
10. Detergent and Rinse Aid dispensers
11. Rating plate
12. Control panel
ADVICE REGARDING THE FIRST TIME USE
After installation, remove the stoppers from the racks and the
retaining elastic elements from the upper rack.
FILLING THE SALT RESERVOIR
The use of salt prevents the formation of LIMESCALE on the
dishes andon the machine’s functional components.
• It is important that the salt reservoir be never empty.
• It is important to set the water hardness.
The salt reservoir is located in the lower part of the
dishwasher
(see PRODUCT DESCRIPTION)
and should be
filled when the
SALT REFILL indicator light
in the
control panel is lit .
1. Remove the lower rack and
unscrew the reservoir cap
(anticlockwise).
2. Only the first time you do this: fill
the salt reservoir with water.
3. Position the funnel (see figure)
and fill the salt reservoir right up
to its edge (approximately 1 kg);
it is not unusual for a little water to
leak out.
4. Remove the funnel and wipe any
salt residue away from the
opening.
1. On-Off/Reset button with indicator light
2. Program selection button
3. Salt refill indicator ligh
4. Rinse Aid refill indicator ligh
5. Program number and delay time indicator
6. Tablet indicator light
7. Display
8. Half Load indicator light
9. Half Load button
10. Delay button
11. START/Pause button with indicator light / Tab
1
2 3 4
5
6 7 8
9
10
11
auf der Bedienblende
leuchtet.
• Switch on the appliance by pressing the ON/OFF button.
• Switch off the appliance by pressing the ON/OFF button.
• Hold down button
for 5 seconds, until you hear a beep.
• Switch on the appliance by pressing the ON/OFF button.
•
•
The current selection level number and the salt indicator light
� � � � � �
Press button
to select the desired hardness level (see
WATER HARDNESS TABLE).
• Switch off the appliance by pressing the ON/OFF button.
Setting is complete!
Water Hardness Table
Level
°dH
German degrees
°fH
French degrees
1
Soft
0 - 6
0 - 10
2
Medium
7 - 11
11 - 20
3
Average
12 - 17
21 - 30
4
Hard
18 - 34
31 - 60
5
Very hard
35 - 50
61 - 90
Make sure the cap is screwed on tightly, so that no detergent can
get into the container during the wash program (this could damage
the water softener beyond repair).
As soon as this procedure is complete, run a program without
loading. The “Pre-Wash” program alone is NOT� � � � � �
Residual saline solution or grains of salt can lead to corrosion,
irreparably damaging the stainless steel components.
The guarantee is not applicable if faults are caused by such
circumstances.
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
s.
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
heating element may be damaged as a result.
Whenever you need to add salt, it is mandatory to complete
the procedure before the beginning of the washing cycle.
SETTING THE WATER HARDNESS
To allow the water softener to work in a perfect way, it is essential
that the water hardness setting is based on the actual water hard-
ness in your house. This information can be obtained from your local
water supplier. The factory setting is for average (3) water hardness.
FILLING THE RINSE AID DISPENSER
A
should be filled when the
RINSE AID REFILL indicator light
B
(110 ml) reference notch of the filling space - avoid spilling it.
NEVER pour the rinse aid directly into the tub.
A
B
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satisfied with the drying results, you can
The current selection level number and rinse aid indicator light flash.
the dishwasher model. The factory setting is specific to the model,
FILLING THE DETERGENT DISPENSER
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
dishwashers.
useof detergent, rinse aid liquid and refined salt is required.
To open the detergent dispenser
press button A.
Introduce the detergent into
the dry dispenser B only.
Place the amount of detergent
for pre-washing directly inside
the tub.
A
B
B
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the TABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
1. Den Behälter
B
durch Drücken und Anheben der Zunge am
Deckel öffnen.
2. Den Klarspüler vorsichtig bis zur maximalen
Füllstandsmarkierung (110 ml) an der Füllöffnung einfüllen
und ein Überlaufen vermeiden. Andernfalls sofort mit einem
trockenen Tuch abwischen.
3. Den Deckel schließen bis er einrastet.
4.
Füllen Sie den Klarspüler NIEMALS direkt ins Innere des
Geschirrspülers.
Klarspülerdosierung
Sollte das Trockenergebnis unzufriedenstellend sein, kann die
Klarspülerdosierung neu eingestellt werden.
• Den Geschirrspüler mit der Taste EIN/AUS einschalten.
• Mit der Taste EIN/AUS ausschalten.
• Drücken Sie die Taste
• Switch on the appliance by pressing the ON/OFF button.
• Switch off the appliance by pressing the ON/OFF button.
• Hold down button
for 5 seconds, until you hear a beep.
• Switch on the appliance by pressing the ON/OFF button.
•
•
The current selection level number and the salt indicator light
� � � � � �
Press button
to select the desired hardness level (see
WATER HARDNESS TABLE).
• Switch off the appliance by pressing the ON/OFF button.
Setting is complete!
Water Hardness Table
Level
°dH
German degrees
°fH
French degrees
1
Soft
0 - 6
0 - 10
2
Medium
7 - 11
11 - 20
3
Average
12 - 17
21 - 30
4
Hard
18 - 34
31 - 60
5
Very hard
35 - 50
61 - 90
Make sure the cap is screwed on tightly, so that no detergent can
get into the container during the wash program (this could damage
the water softener beyond repair).
As soon as this procedure is complete, run a program without
loading. The “Pre-Wash” program alone is NOT� � � � � �
Residual saline solution or grains of salt can lead to corrosion,
irreparably damaging the stainless steel components.
The guarantee is not applicable if faults are caused by such
circumstances.
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
s.
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
heating element may be damaged as a result.
Whenever you need to add salt, it is mandatory to complete
the procedure before the beginning of the washing cycle.
SETTING THE WATER HARDNESS
To allow the water softener to work in a perfect way, it is essential
that the water hardness setting is based on the actual water hard-
ness in your house. This information can be obtained from your local
water supplier. The factory setting is for average (3) water hardness.
FILLING THE RINSE AID DISPENSER
A
should be filled when the
RINSE AID REFILL indicator light
B
(110 ml) reference notch of the filling space - avoid spilling it.
NEVER pour the rinse aid directly into the tub.
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satisfied with the drying results, you can
The current selection level number and rinse aid indicator light flash.
the dishwasher model. The factory setting is specific to the model,
FILLING THE DETERGENT DISPENSER
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
dishwashers.
useof detergent, rinse aid liquid and refined salt is required.
To open the detergent dispenser
press button A.
Introduce the detergent into
the dry dispenser B only.
Place the amount of detergent
for pre-washing directly inside
the tub.
A
B
B
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the TABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
drei Mal - ein Piepton ertönt.
• Mit der Taste EIN/AUS einschalten.
• Die Nummer der aktuell ausgewählten Stufe und die
Klarspülernachfüllanzeige blinken.
• Drücken Sie die Taste
• Switch on the appliance by pressing the ON/OFF button.
• Switch off the appliance by pressing the ON/OFF button.
• Hold down button
for 5 seconds, until you hear a beep.
• Switch on the appliance by pressing the ON/OFF button.
•
•
The current selection level number and the salt indicator light
� � � � � �
Press button
to select the desired hardness level (see
WATER HARDNESS TABLE).
• Switch off the appliance by pressing the ON/OFF button.
Setting is complete!
Water Hardness Table
Level
°dH
German degrees
°fH
French degrees
1
Soft
0 - 6
0 - 10
2
Medium
7 - 11
11 - 20
3
Average
12 - 17
21 - 30
4
Hard
18 - 34
31 - 60
5
Very hard
35 - 50
61 - 90
Make sure the cap is screwed on tightly, so that no detergent can
get into the container during the wash program (this could damage
the water softener beyond repair).
As soon as this procedure is complete, run a program without
loading. The “Pre-Wash” program alone is NOT� � � � � �
Residual saline solution or grains of salt can lead to corrosion,
irreparably damaging the stainless steel components.
The guarantee is not applicable if faults are caused by such
circumstances.
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
s.
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
heating element may be damaged as a result.
Whenever you need to add salt, it is mandatory to complete
the procedure before the beginning of the washing cycle.
SETTING THE WATER HARDNESS
To allow the water softener to work in a perfect way, it is essential
that the water hardness setting is based on the actual water hard-
ness in your house. This information can be obtained from your local
water supplier. The factory setting is for average (3) water hardness.
FILLING THE RINSE AID DISPENSER
A
should be filled when the
RINSE AID REFILL indicator light
B
(110 ml) reference notch of the filling space - avoid spilling it.
NEVER pour the rinse aid directly into the tub.
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satisfied with the drying results, you can
The current selection level number and rinse aid indicator light flash.
the dishwasher model. The factory setting is specific to the model,
FILLING THE DETERGENT DISPENSER
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
dishwashers.
useof detergent, rinse aid liquid and refined salt is required.
To open the detergent dispenser
press button A.
Introduce the detergent into
the dry dispenser B only.
Place the amount of detergent
for pre-washing directly inside
the tub.
A
B
B
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the TABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
, um den Stand der gelieferten
Klarspülermenge auszuwählen.
• Mit der Taste EIN/AUS ausschalten.
Die Einstellung ist abgeschlossen!
Die Klarspülerstufe kann auf NULL eingestellt werden. In diesem
Fall wird kein Klarspüler ausgegeben. Die Kontrollleuchte zur
ANZEIGE DES FEHLENDEN KLARSPÜLERS leuchtet nicht mehr
auf. Je nach Gerätemodell können bis max. 5 Stufen eingestellt
werden. Die Werkseinstellung ist abhängig vom Modell. Bitte
befolgen Sie die Anweisungen oben, um dies für Ihr Gerät zu
überprüfen.
• Wenn Sie bläuliche Streifen auf dem Geschirr sehen, stellen Sie
eine niedrigere Zahl ein (1-2).
• Wenn Wassertropfen oder Kalkablagerungen auf dem Geschirr
sind, eine höhere Zahl einstellen (3-4).
Einfüllen des Spülmittels
Die Verwendung von Spülmittel, das nicht für Geschirrspüler
entwickelt wurde, ist, kann zu Funktionsstörungen oder Schäden
am Gerät führen.
Die besten Spül- und Trockenergebnisse erhalten Sie nur durch
den kombinierten Einsatz von Spülmittel, flüssigem Klarspüler
und Regeneriersalz. Es wird dringend empfohlen, phosphat- und
chlorfreie Spülmitteln zu verwenden, die Umwelt nicht zu sehr
belasten. Ein gutes Spülergebnis hängt auch von einer korrekten
Spülmitteldosierung ab.
Eine zu hohe Dosierung ist nicht gleichzusetzen mit einem
besseren Spülergebnis, man belastet dadurch nur die Umwelt. Die
Dosierung kann dem jeweiligen Verschmutzungsgrad angepasst
werden. Bei einer normalen Verschmutzung ca.
25 g (in Pulverform) bzw. 25 ml (flüssig) verwenden und einen
zusätzlichen Teelöffel Spülmittel direkt in den Geschirrspüler
geben. Werden Spülmitteltabs verwendet, reicht ein Tab aus.
Für nur leicht verschmutztes Geschirr, oder für Geschirr, das
vorher unter laufendem Wasser abgespült wurde, kann die
Spülmittelmenge erheblich reduziert werden (Minimum 20 g/ml)
z.B das Pulver/Gel nicht in das Gerät geben.
Drücken Sie zum Öffnen des Spülmittelfachs Taste C.
Füllen Sie das Spülmittel ausschließlich in das trockene Fach
D ein.
Die für den Vorspülgang benötigte Spülmittelmenge wird
direkt in den Geschirrspüler gegeben.
1. Hinsichtlich der Dosierung
verweisen wir auf die zuvor
erwähnte Information, in
der die richtige Menge
angegeben ist. Im Fach
D
sind Anzeigen, die bei der
Spülmitteldosierung helfen.
2. Entfernen Sie eventuelle
Spülmittelrückstände von
den Kanten der Kammern
und schließen Sie den Deckel
so, dass er einrastet.
3. Schieben Sie den Deckel der Spülmittelkammer zum Schließen
nach oben, bis er einrastet.
Die Spülmittelkammer öffnet sich automatisch zum richtigen
Zeitpunkt des jeweils gewählten Programms. Werden
Kombispülmittel verwendet, dann empfehlen wir, die Option TAB
zu verwenden.
Damit werden die Programme dem verwendeten Spülmittel
angepasst, um das bestmögliche Spülergebnis zu erhalten.
• Switch on the appliance by pressing the ON/OFF button.
• Switch off the appliance by pressing the ON/OFF button.
• Hold down button
for 5 seconds, until you hear a beep.
• Switch on the appliance by pressing the ON/OFF button.
•
•
The current selection level number and the salt indicator light
� � � � � �
Press button
to select the desired hardness level (see
WATER HARDNESS TABLE).
• Switch off the appliance by pressing the ON/OFF button.
Setting is complete!
Water Hardness Table
Level
°dH
German degrees
°fH
French degrees
1
Soft
0 - 6
0 - 10
2
Medium
7 - 11
11 - 20
3
Average
12 - 17
21 - 30
4
Hard
18 - 34
31 - 60
5
Very hard
35 - 50
61 - 90
Make sure the cap is screwed on tightly, so that no detergent can
get into the container during the wash program (this could damage
the water softener beyond repair).
As soon as this procedure is complete, run a program without
loading. The “Pre-Wash” program alone is NOT� � � � � �
Residual saline solution or grains of salt can lead to corrosion,
irreparably damaging the stainless steel components.
The guarantee is not applicable if faults are caused by such
circumstances.
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
s.
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
heating element may be damaged as a result.
Whenever you need to add salt, it is mandatory to complete
the procedure before the beginning of the washing cycle.
SETTING THE WATER HARDNESS
To allow the water softener to work in a perfect way, it is essential
that the water hardness setting is based on the actual water hard-
ness in your house. This information can be obtained from your local
water supplier. The factory setting is for average (3) water hardness.
FILLING THE RINSE AID DISPENSER
A
should be filled when the
RINSE AID REFILL indicator light
B
(110 ml) reference notch of the filling space - avoid spilling it.
NEVER pour the rinse aid directly into the tub.
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satisfied with the drying results, you can
The current selection level number and rinse aid indicator light flash.
the dishwasher model. The factory setting is specific to the model,
FILLING THE DETERGENT DISPENSER
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
dishwashers.
useof detergent, rinse aid liquid and refined salt is required.
To open the detergent dispenser
press button A.
Introduce the detergent into
the dry dispenser B only.
Place the amount of detergent
for pre-washing directly inside
the tub.
A
B
B
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the TABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
C
D
B
A
Summary of Contents for finputsad
