IKEA finputsad, Manual

Page: 10 / 68

ENGLISH 10
1. Check water connection
Check that the dishwasher is connected to the water supply
and that the tap is open.
2. Switch on the dishwasher
Open the door and press the ON/OFF button.
3. Load the racks (see LOADING THE RACKS)
4. Filling the detergent dispenser
(see PROGRAMS TABLE).
5. Choose the program and customise the cycle
Select the most appropriate program in accordance with
the type of crockery and its soiling level (see PROGRAMS
DESCRIPTION) by pressing the button.
Select the desired options (see FUNCTIONS).
6. Start
Start the wash cycle by pressing START/Pause button (led
is lit) and closing the door within 4 sec. When the program
starts you hear a single beep. If the door was not closed
within 4sec., the alarm sound will be played. In this case,
open the door, press START/Pause button and close the door
again within 4 sec.
7. End of wash cycle
The end of the wash cycle is indicated by beeps and by the
flashing of the wash cycle number on the display. Open the
door and switch off the appliance by pressing the ON/OFF
button.
Wait for a few minutes before removing the crockery - to
avoid burns. Unload the racks, beginning with the lower one.
The machine will switch off automatically during certain
extended periods of inactivity, in order to minimise
electricity consumption. If the crockery is only lightly soiled
or if it has been rinsed with water before being placed in the
dishwasher, reduce the amount of detergent used
accordingly.
Modifying a running program
If a wrong program was selected, it is possible to change it,
provided that it has only just begun: open the door, press and
hold the ON/OFF button, the machine will switch off.
Switch the machine back on using the ON/OFF button and select
the new wash cycle and any desired options; Start the wash
cycle by pressing START/Pause button and closing the door
within 4 sec.
Adding extra crockery
Without switching off the machine, open the door (START/
Pause led starts blinking) (be ware of HOT steam!) and place the
crockery inside the dishwasher. Press the START/Pause button
and close the door within 4 sec., the cycle will resume from the
point at which it was interrupted.
Accidental interruptions
If the door is opened during the wash cycle, or if there is a
power cut, the cycle stops. Press the START/Pause button and
close the door within 4 sec., the cycle will resume from the point
at which it was interrupted.
Daily Use
If an option is not compatible with the selected program , the corresponding LED flashes rapidly 3 times
If you use powder or liquid detergent, this option
should be off.
To confirm the change and exit from the Control Menu please
appears on the display; each time you press the button,
The DELAY function cannot be set once a wash cycle
To wash only the specific rack, press this button repeatedly:
reduce the amount of detergent accordingly.
If upper rack is removed, please apply detergent
directly to tub instead of detergent dispenser.
A higher temperature during the final rinse and an extended
A LED light projected on the floor indicates that the
stays off during the cycle and flashes at the end of the
c) The light stays on during the cycle and flashes at the
first few seconds or the entire duration of the countdown,
to confirm the selection.
Operation Indicator will not flash at the end of cycle.
FLEXIBLE WASH
If there are not many dishes to be washed, a half
loading may be used in order to save water, electricity
and detergent.
Select the program and then press the FLEXIBLE
WASH button: the symbol of the chosen rack will
appear on the display.
By default the appliance washes dishes in all racks.
To wash only the specific rack, press this button
repeatedly:
If an option is not compatible with the selected program , the corresponding LED flashes rapidly 3 times
If you use powder or liquid detergent, this option
should be off.
To confirm the change and exit from the Control Menu please
appears on the display; each time you press the button,
The DELAY function cannot be set once a wash cycle
To wash only the specific rack, press this button repeatedly:
reduce the amount of detergent accordingly.
If upper rack is removed, please apply detergent
directly to tub instead of detergent dispenser.
A higher temperature during the final rinse and an extended
A LED light projected on the floor indicates that the
stays off during the cycle and flashes at the end of the
c) The light stays on during the cycle and flashes at the
first few seconds or the entire duration of the countdown,
to confirm the selection.
Operation Indicator will not flash at the end of cycle.
shown on the display (only lower rack)
shown on the display (only upper rack)
shown on the display (only cutlery rack)
shown on the display (option is OFF and the appliance
will wash dishes in all racks).
Remember to load the upper or lower rack only, and to reduce
the amount of detergent accordingly. If upper rack is removed,
please apply detergent directly to tub instead of detergent
dispenser.
appears on the display; each time you press the button,
The DELAY function cannot be set once a wash cycle
has been started.
NaturalDry
(INSTALLATION GUIDE)
E d
To confirm the change and exit from the Control Menu please
DELAY
1 12
Duration of
(h:min)
**)
(litres/cycle) (kWh/cycle)
50° 2:45 12.0 0.92 1
Eco
2
Conventional
wash and dry
55° 2:00 15.0 1.35
3
Intensive 65° - 2:30 15.0 1.50
4
Fast 50°
-
- 0:55 11.5 1.10
5
Sanitizing 65° - 1:40 11.5 1.30
6
Pre-Wash -
-
- 0:10 4.5 0.01
7
Self-Clean 65°
-
-
0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
DELAY
The start time of the program may be delayed for a
period of time between 1 and 12 hours.
1. Press the DELAY button: the corresponding «h»
symbol appears on the display; each time you press
the button, the time (1h, 2h, etc. up to max. 12h) from
the start of the selected wash cycle will be increased.
2. Select the wash program, press the START/PAUSE
button and within 4 seconds close the door: the timer
will begin counting down.
3. Once this time has elapsed, the indicator light «h»
switches off and the wash cycle begins.
To adjust the delay time and select a shorter period
of time, press the DELAY button. To cancel it, press
the button repeatedly until the selected delayed start
indicator light «h» switches off.
The DELAY function cannot be set once a wash
cycle has been started.
If an option is not compatible with the selected program , the corresponding LED flashes rapidly 3 times
If you use powder or liquid detergent, this option
should be off.
To confirm the change and exit from the Control Menu please
appears on the display; each time you press the button,
The DELAY function cannot be set once a wash cycle
To wash only the specific rack, press this button repeatedly:
reduce the amount of detergent accordingly.
If upper rack is removed, please apply detergent
directly to tub instead of detergent dispenser.
A higher temperature during the final rinse and an extended
A LED light projected on the floor indicates that the
stays off during the cycle and flashes at the end of the
c) The light stays on during the cycle and flashes at the
first few seconds or the entire duration of the countdown,
to confirm the selection.
Operation Indicator will not flash at the end of cycle.
SHORT TIME
This option can be used to reduce the duration of the
main programs while maintaining the same washing
and drying performance levels. After selecting the
program, press the SHORT TIME button and the
indicator light will switch on. To deselect the option,
press the same button again.
If an option is not compatible with the selected program , the corresponding LED flashes rapidly 3 times
If you use powder or liquid detergent, this option
should be off.
To confirm the change and exit from the Control Menu please
appears on the display; each time you press the button,
The DELAY function cannot be set once a wash cycle
To wash only the specific rack, press this button repeatedly:
reduce the amount of detergent accordingly.
If upper rack is removed, please apply detergent
directly to tub instead of detergent dispenser.
A higher temperature during the final rinse and an extended
A LED light projected on the floor indicates that the
stays off during the cycle and flashes at the end of the
c) The light stays on during the cycle and flashes at the
first few seconds or the entire duration of the countdown,
to confirm the selection.
Operation Indicator will not flash at the end of cycle.
EXTRA DRY
To improve the drying of the dishes, after selecting
the program, press the EXTRA DRY button and the
indicator light comes on. A higher temperature
during the final rinse and an extended drying phase
allow for improving drying. To deselect the option,
press the same button again. The EXTRA DRY option
results in the lengthening of the wash cycle.
1. CHECK WATER CONNECTION
2. SWITCH ON THE DISHWASHER
3.
4. LOAD THE RACKS
(see LOADING THE RACKS)
FILLING THE DETERGENT DISPENSER
(see PROGRAMS TABLE).
5.
6.
7.
CHOOSE THE PROGRAM AND CUSTOMISE THE CYCLE
(see PROGRAMS
DESCRIPTION)
(see OPTIONS AND FUNCTIONS)
START
END OF WASH CYCLE
flashing of the wash cycle number on the display. Open the
The machine will switch off automatically during certain
extended periods of inactivity, in order to minimise electri-
city consumption. If the crockery is only lightly soiled or
if it has been rinsed with water before being placed in the
dishwasher, reduce the amount of detergent used accordingly.
MODIFYING A RUNNING PROGRAM
ON/OFF
ON/OFF
the new wash cycle and any desired options; Start the wash cycle
START/Pause
ADDING EXTRA CROCKERY
START/Pause
be ware of HOT steam!
START/Pause
ACCIDENTAL INTERRUPTIONS
START/Pause
DAILY USE
1. ECO - Normally soiled crockery. Standard program, the most efficient in terms of its combined energy and water
consumption.
2. NORMAL - Mixed soil. For normally soiled dishes with dried food residues.
3. INTENSIVE
- Program recommended for heavily soiled crockery, especially suitable for pans and saucepans (not to be used
for delicate items).
4. PRE-WASH - Use to refresh crockery planned to be washed later. No detergent to be used with this program.
5. FAST - Normally soiled crockery. Everyday cycle, that ensures optimal cleaning performance in shorter time.
6. SANITIZING - Normally or heavily soiled crockery, with additional antibacterial wash. Can be used to perform
maintenance of the dishwasher.
7. SELF- CLEAN - Program to be used to perform maintenance of the dishwasher. It cleans the interior of the appliance
using hot water.
(see CONTROL PANEL)
If an option is not compatible with the selected program
see PROGRAMS TABLE
, the corresponding LED � � � �rapidly 3 times
and beeps will sound. The option will not be enabled.
HALF LOAD
Remember to halve the amount of detergent.
The DELAY function cannot be set once a wash cycle
has been started.
TABLET (Tab)
If you use powder or liquid detergent, this option
should be off.
E d
To confirm the change and exit from the Control Menu please
TABLET (Tab)
This setting allows you to optimize the performance
of the program according to the type of detergent
used. Press the START/PAUSE button for 3 seconds
(the corresponding symbol will light up) if you use
combined detergents in tablet form (rinse aid, salt
and detergent in 1 dose).
If you use powder or liquid detergent, this option
should be off.
If an option is not compatible with the selected program , the corresponding LED flashes rapidly 3 times
If you use powder or liquid detergent, this option
should be off.
To confirm the change and exit from the Control Menu please
appears on the display; each time you press the button,
The DELAY function cannot be set once a wash cycle
To wash only the specific rack, press this button repeatedly:
reduce the amount of detergent accordingly.
If upper rack is removed, please apply detergent
directly to tub instead of detergent dispenser.
A higher temperature during the final rinse and an extended
A LED light projected on the floor indicates that the
stays off during the cycle and flashes at the end of the
c) The light stays on during the cycle and flashes at the
first few seconds or the entire duration of the countdown,
to confirm the selection.
Operation Indicator will not flash at the end of cycle.
OPERATION INDICATOR
A LED light projected on the floor indicates that
the dishwasher is working. One of the following
operating modes can be selected:
a) Disabled function.
b) When the cycle starts the light goes on for a few
seconds, stays off during the cycle and flashes at the
end of the cycle.
c) The light stays on during the cycle and flashes at
the end of the cycle (default mode).
If the delayed start was set, the light goes on either
for the first few seconds or the entire duration of the
countdown, based on whether mode b) or c) was set.
The light goes off every time the door is opened.
To select the mode you prefer, switch on the machine,
hold down button
• Switch on the appliance by pressing the ON/OFF button.
• Switch off the appliance by pressing the ON/OFF button.
• Hold down button for 5 seconds, until you hear a beep.
• Switch on the appliance by pressing the ON/OFF button.
•
•
The current selection level number and the salt indicator light
� � � � � �
Press button to select the desired hardness level (see
WATER HARDNESS TABLE).
• Switch off the appliance by pressing the ON/OFF button.
Setting is complete!
Water Hardness Table
Level
°dH
German degrees
°fH
French degrees
1 Soft 0 - 6 0 - 10
2 Medium 7 - 11 11 - 20
3 Average 12 - 17 21 - 30
4 Hard 18 - 34 31 - 60
5 Very hard 35 - 50 61 - 90
Make sure the cap is screwed on tightly, so that no detergent can
get into the container during the wash program (this could damage
the water softener beyond repair).
As soon as this procedure is complete, run a program without
loading. The “Pre-Wash” program alone is NOT� � � � � �
Residual saline solution or grains of salt can lead to corrosion,
irreparably damaging the stainless steel components.
The guarantee is not applicable if faults are caused by such
circumstances.
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � s.
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
heating element may be damaged as a result.
Whenever you need to add salt, it is mandatory to complete
the procedure before the beginning of the washing cycle.
SETTING THE WATER HARDNESS
To allow the water softener to work in a perfect way, it is essential
that the water hardness setting is based on the actual water hard-
ness in your house. This information can be obtained from your local
water supplier. The factory setting is for average (3) water hardness.
FILLING THE RINSE AID DISPENSER
A
should be filled when the RINSE AID REFILL indicator light
B
(110 ml) reference notch of the filling space - avoid spilling it.
NEVER pour the rinse aid directly into the tub.
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satisfied with the drying results, you can
The current selection level number and rinse aid indicator light flash.
the dishwasher model. The factory setting is specific to the model,
FILLING THE DETERGENT DISPENSER
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
dishwashers.
useof detergent, rinse aid liquid and refined salt is required.
To open the detergent dispenser
press button A.
Introduce the detergent into
the dry dispenser B only.
Place the amount of detergent
for pre-washing directly inside
the tub.
A
B
B
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the TABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
until one of the three letters
Functions