IFM ZZ0814 Instructions For Setup Download Page 28 | Manualshive

Page: 28 / 36

background image

ZZ0814 ZZ0815 ZZ0816 ZZ0817

28

Data exchange procedure with result file

Fig. 15: Data exchange with result file

8.4.5 Structure of the feedback file

The feedback file generated by the ZZ1124 is saved in JSON file format. The feedback file contains all
the important information that the higher-level system requires. The feedback file must be fetched from
the file system of the ZZ1124 by the higher-level system and deleted.

The feedback file has the following structure:

«
...
26
27
28
29
30
...
»

Summary of Contents for ZZ0814





































Reviews:

No comments

Related manuals for ZZ0814

Brand: Panamax Pages: 16

Brand: K&G GROEP Pages: 27

BrewZilla 100L - Gen 4

Brand: KegLand Pages: 48

Sysmac NX-TBX01

Brand: Omron Pages: 172

Brand: Zepro Pages: 64

Brand: Jensen Pages: 41

Brand: Hama Pages: 76

Brand: Ravaglioli Pages: 54

Brand: Launch Pages: 31

Brand: Liko Pages: 14

Brand: Panasonic Pages: 22

Brand: Panasonic Pages: 27

Brand: Panasonic Pages: 33

Brand: Panasonic Pages: 15

Brand: Oakcastle Pages: 25

DIAPERFEEDER IP54 DUOLOOP

Brand: btsr Pages: 57

Brand: PVI Pages: 12

Brand: Mesa Pages: 33

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands