background image

19

UK

FOU2 Response of the analogue signal when a diagnostic case is signalled: 

 

> Instead of the measured temperature value a defined current value according 

to Namur NE43 is provided (On: 21�5 mA; OFF: 3�5 mA)

dOU1

Response of the diagnostic switching output when a diagnostic case is signalled:

 

> Output opens / closes / pulsates depending on the category of the diagnostic 

case�

Setting options see Table 4 

→ 5.3.5

P-n

Switching logic for the diagnostic switching output: pnp or npn�

HI

Read max� value of the temperature measured in the process�

LO

Read min� value of the temperature measured in the process�

Fnr

Read fault number 

→ 11 Fault correction

rES

Restoring the factory settings�

It is recommended to note down your own settings before carrying out a 

reset 

(→ 12 Factory setting)

9  Operation

When the supply voltage is applied, the unit is in the RUN mode after a power-on 

delay time of 8 s (= normal operating mode)� It carries out its measurement and 

evaluation functions and provides output signals according to the set parameters�

10  Technical data

Technical data and scale drawing at www�ifm�com�

10.1  Setting range for drW / drA

Medium temperature

Setting range

-10���100 °C

14���212 °F

0�2���5 K

-25���0 °C 

-13���32 °F

0�3���5 K

> 100 °C

> 212 °F

   x...5 K (→ chart)

Summary of Contents for TAD 81 Series























Reviews: