manualshive.com logo in svg

IFM TAD 81 Series, Operating Instructions Manual, Page: 18 / 22

Share
Download
IFM TAD 81 Series Operating Instructions Manual Download Page 18

18

 

►

Connect the unit via the IO-Link interface to a PC or PLC with suitable 

parameter setting software� 

IO-Link interface for connection of the sensor to a PC → www.ifm.com.

8.1  Adjustable parameters

Uni

Setting of the standard unit of measurement: °C or °F�

OU2

Configuration of the analogue signal: I = 4���20 mA or Ineg = 20���4 mA

ASP

Analogue start point for measured temperature value

AEP

Analogue end point for measured temperature value

drW

Drift warning threshold: If this value of the temperature deviation is exceeded, a 

diagnostic message of the category "warning" is provided with setting [drEd] = 

OFF� 

°C/°F = Maximum permitted temperature deviation of both sensor elements from 

the mean value� Setting range 

→ 10.1

�

OFF = Drift warning deactivated�

drA

Drift alarm threshold: If this value of the temperature deviation is exceeded, a 

diagnostic message of the category "alarm" is provided with setting [drEd] = 

ONdr or OFF� 

°C/°F = Maximum permitted temperature deviation of both sensor elements from 

the mean value� Setting range 

→ 10.1

�

OFF = Drift alarm deactivated�

drF

Drift failure threshold: [drF] = drA + 3 K; if this value of the temperature deviation 

is exceeded, a diagnostic message of the category "failure" is provided� 

• drF cannot be set but results from the setting of drA�

• Setting drA = OFF automatically results in: drF = 8 K

ddr

Delay of the drift detection�

ddr = Time span (0�5���300 min) for which a drift value must be above the 

warning threshold drW or alarm threshold drA so that a diagnostic signal 

is provided�

drEd

Setting of the diagnostic cases 

(→ 5.3.3)

 for which diagnostic messages are 

provided� 

ON = Diagnostic cases of the category "failure" are signalled�

ONdr = Diagnostic cases of the categories "alarm" and "failure" are signalled�

OFF = Diagnostic cases of the categories "warning", "alarm" and "failure" are 

signalled�

Summary of Contents for TAD 81 Series























Reviews:

No comments