background image

SDP110

Air gap sensor

32

12 Troubleshooting

The unit has many self-diagnostic options. It monitors itself automatically during operation.

Warnings and error states are displayed even if the display is switched off. Error indications are also
available via IO-Link.

The status signals are classified according to NAMUR recommendation NE107.

If several diagnostic events occur simultaneously, only the diagnostic message of the event with the
highest priority is displayed.

If a process value fails, the other process values are still available. Exception: If the process value for
flow fails, no other process values are output.

Additional diagnostic functions are available via IO-Link 

Ò

 IO-Link interface description at

documentation.ifm.com

.

12.1 Error messages

Display

Problem/remedy

• Title line: ERROR

• Process value line: ERROR

Unit faulty / malfunction.

u

Replace the unit.

No display

• Supply voltage too low.

u

Check the supply voltage.

• Display switched off.

u

Check whether setting [diS.B] = OFF and change setting if
necessary.

• Title line: Running

• Process value line: NoData

Process value invalid.

u

Check process conditions.

• Title line: Parameter Error

• Process value line: PARA

Parameter setting outside the valid range.

u

Check parameter setting.

In the event of an error, the outputs react according to the setting under [FOU].

12.2 Warning messages

Display

Problem/remedy

• Title line: Short circuit OUT1/OUT2

• Process value line: ---

• Switching status LEDs for OUT1 and OUT2 flashing

Short circuit in both outputs.

u

Check OUT1 and OUT2 for short circuit or excessive
current.

• Title line: Short circuit OUT1

• Process value line: ---

• Switching status LED for OUT1 flashing

Short circuit output 1.

u

Check OUT1 for short circuit or excessive current.

• Title line: Short circuit OUT2

• Process value line: ---

• Switching status LED for OUT2 flashing

Short circuit output 2.

u

Check OUT2 for short circuit or excessive current.

• Title line: Under limit

• Process value line: UL

Setting range not reached.

u

Check the measuring range.

• Title line: Over limit

• Process value line: OL

Setting range exceeded.

u

Check the measuring range.

• Title line: ---

• Process value line: Lock via key

Setting keys on the unit locked, parameter change rejected.

u

Unlock unit.

Summary of Contents for SDP110




































Reviews: