manualshive.com logo in svg

IFM O1D300, Operating Instructions Manual, Page: 26 / 35

Share
Download
IFM O1D300 Operating Instructions Manual Download Page 26

26

10.3.2  Setting the display

 

►

Change to [EF]�

 

►

Select [diS] and make settings�

2 settings can be selected:

• [ON] = the measured value display is activated in the Run mode� 

Update of the measured values every 600 ms�

• [OFF] =  The measured value display is deactivated in the Run mode� 

Press one button to indicate the current measured value for 15 s�  

The update of the measured value only refers to the display� It has no 

effect on the outputs�

 

►

Confirm with [MODE/ENTER]�

The LEDs remain active even if the display is deactivated�

10.3.3  Configure OUT1

 

►

Select [OU1] and set the switching functions�

Switching functions:

• [Hno] = hysteresis function / normally open

• [Hnc] = hysteresis function / normally closed 

• [Fno] = window function / normally open

• [Fnc] = window function / normally closed

 

►

Confirm with [MODE/ENTER]�

10.3.4  Setting of the switch points for hysteresis function OUT1

 

►

In [OU1] select the output function [Hno] or [Hnc]�

 

►

Confirm with [MODE/ENTER]� 

 

►

Select [SP1] and set the set point�

 

►

Confirm with [MODE/ENTER]�

 

►

Select [rP1] and set the reset point�

 

►

Confirm with [MODE/ENTER]�

10.3.5  Setting of the switch points for window function OUT1

 

►

In [OU1] select the output function [Fno] or [Fnc]�

 

►

Confirm with [MODE/ENTER]�

 

►

Select [SP1] and set the upper limit value�

 

►

Confirm with [MODE/ENTER]�

 

►

Select [rP1] and set the lower limit value�

 

►

Confirm with [MODE/ENTER]�

Summary of Contents for O1D300




































Reviews:

No comments