background image

22

10.1.3  Electronic lock

The unit can be locked electronically to prevent unauthorised setting� On delivery 

the unit is not locked�

Locking

 

Make sure that the unit is in the normal 

operating mode�

 

Keep [MODE/ENTER] + [SET] pressed 

until [Loc] is displayed�

 

> The unit is locked�
[Loc] is displayed briefly if you try to change parameter values on the locked unit during 

operation�

Unlocking

 

Keep [MODE/ENTER] + [SET] ] pressed 

until [uLoc] is displayed�

 

> The unit is unlocked�

Timeout

If no button is pressed for 15 s during the setting procedure, the unit changes to the 

Run mode with unchanged values�

10.2  Entering the reference level (unit on delivery)

On delivery the unit is not operational� The reference level has to be set first� The 

complete parameter setting menu cannot be accessed before this has been done�
There are three different ways to define the reference level�

10.2.1  Free choice of the tank height

If the height of the tank (distance between the front lens of the O1D to the tank 

bottom) is known, it can be entered without the unit being mounted� The distance 

entered is used as reference level�

1

 

Apply operating voltage�

 

> Initial display is shown�

Summary of Contents for O1D300




































Reviews: