IFM DTE103 Device Manual Download

Page: 31 / 74

11.3.3 Setup “Transponder data block length”

Parameter

Description

Transponder data block

size

Block size in bytes of the RFID tag:

4/8/16/32/64/128/255
Please refer to the data sheet of the RFID tag for the block size

Only necessary for IO-channel mode “RWH_RW”

The value must be input as hexadecimal number .
Example: For 32 byte the setting shall be “20”

Select line 3 “PS CoE 0x4000:03” in tab “Startup” of the device . Enter the requested value .

11.3.4 Setup “Overload and Overcurrent detection”

With the parameter “Overload detection” the output current at terminal L+ can be controlled .
With the parameter “Overcurrent detection” the output current at terminal C/Qo can be controlled .

Parameter

Description

Overload detection

On: Overload on terminal L+ of the IO-port is supervised ( default )

The output current is limited to 500 . . .700 mA
Off: Supervision is off

The output current is not supervised and may increase up to 1200

mA . In this case the output driver of the IO-channel is protect against

overtemperature .

Overcurrent detection

On: Overcurrent on terminal C/Qo of the IO-port is supervised ( default )

The output current is limited to 500 mA
Off: Supervision is off

The output current is not supervised and may increase up to 600 mA . In this

case the output driver of the IO-channel is protect against overtemperature .

Select line 4 and 5 with “PS CoE 0x4000:04” and “PS CoE 0x4000:05” in tab “Startup” of the device .

Enter the requested value .

The maximum current consumption at terminal AUX + / AUX - may not exceed 3 A .

11.3.5 Setup “Read UID edge controlled”

If the UID of the RFID tag shall be read only when a “Read UID” command is started than the value shall

be set to “01” . (Activate synchronous mode)
If the UID of the RFID tag shall be read continuously without sending a command from the EtherCAT

master the value “00” shall be used . (Activate asynchronous mode)
Parameter valid only for IO-channel mode “RWH_RW”

Parameter

Description

UID edge controlled

Edge-controlled reading of the UID via bit RD in the control word of the

module RWH_RW
Default: Off

Select line 6 with “PS CoE 0x4000:06” in tab “Startup” of the device . Enter the requested value .

Repeat the setup for all used IO-channels .

Summary of Contents for DTE103











































































Search results

Summary of Contents for DTE103

Reviews:

Related manuals for DTE103

Brands by name

Popular brands

IFM DTE103, Device Manual

Search results

Summary of Contents for DTE103

Reviews:

Related manuals for DTE103

Brands by name

Popular brands