IFM AC1401/02 Device Manual Supplement Download Page 14 | Manualshive

Page: 14 / 123

background image

14

ifm

Device Manual Supplement: Acyclic data records and Command interface (AC14 and AC4S)

2017 / 09

Acyclic data records

>

3.3.2

Execution control flags

7161

The execution control flags provide information about the execution control of the AS-i master. The
flags are updated by the AS-i master immediately after each change.

The execution control flags are saved in the following register:

Execution control flags

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

–

NOPF CCOK

PE

–

DEA

AAE

POK

OR

APF

NOA

CA

AA

AN

S0

COK

Legend:

Flag

Designation

Description

Initial value at power-on

COK

Config_OK

1 (TRUE):

The configuration of all AS-i slaves on the
network corresponds to the projection
data (CDI=PCD for all activated slaves)
&& (LDS=LPS=LAS)
Exception:
Flag APF = 1 and LPS = empty, then
COK = 1

0 (FALSE)

S0

LDS.0

1 (TRUE):

Slave with address 0 found

0 (FALSE)

AN

Auto_Address_Assign

1 (TRUE):

Auto addressing possible
(protected mode = active && auto
addressing = active && PCD = CDI &&
LDS <=



LPS)

0 (FALSE)

AA

Auto_Address_Available

1 (TRUE):

All the necessary conditions for auto
addressing are fulfilled. The master waits
for slave 0.

0 (FALSE)

CA

Configuration_Active

0 (FALSE):
1 (TRUE):

Master in protected mode
Master in projection mode

0 (FALSE)

NOA

Normal_Operation_Active

1 (TRUE):

Master is in the normal mode
(The AS-i master has communicated with
at least one slave since the last offline
phase. Even if the slave disappears after
this, the signal will remain set.)

0 (FALSE)

APF

Asi_Power_Fail

0 (FALSE):
1 (TRUE):

AS-i voltage OK
AS-i voltage too low

1 (TRUE)

OR

Offline_Ready

1 (TRUE):

Master has gone through the offline
phase and waits for:
APF = 0 and a timeout of 1s

0 (FALSE)

POK

Periphery_OK

1 (TRUE):

No peripheral faults present, all bits of
LPF = 0.

0 (FALSE)

AAE

Auto_Address_Enable

1 (TRUE):

Auto addressing switched on
(Echo of Set_Auto_Address_Enable of
host)

0 (FALSE)

DEA

Data_Exchange_Active

1 (TRUE):

Data exchange between master and
slaves activated (reflects DEA of host
flags)

1 (TRUE)

0 (FALSE):

Instead of the data exchange, ReadID is
continually executed on the slaves.

PE

Protocol Error

1 (TRUE):
0 (FALSE):

CTT protocol error
No CTT protocol error

0 (FALSE)

«
...
12
13
14
15
16
...
»

Summary of Contents for AC1401/02




























































































































Reviews:

No comments

Related manuals for AC1401/02

Brand: Sangoma Pages: 2

Brand: NetComm Wireless Pages: 28

Brand: Moeller Pages: 78

SMK Access Station Mini

Brand: Sigfox Pages: 17

POWER LEADER GEH-6505A

Brand: GE Pages: 24

Brand: GE Pages: 16

PACSystems RX3i Genius

Brand: GE Pages: 79

ATEUS EasyGate 501309E

Brand: 2N Telekomunikace Pages: 2

TOOLBOX-ETH-GPRS

Brand: Ewattch Pages: 14

Brand: Wireless Sensors Pages: 35

VPN Firewall Brick 20

Brand: Lucent Technologies Pages: 52

SURFboard SBG6900-AC

Brand: Arris Pages: 80

Brand: ACT'L Pages: 30

Brand: Pace Pages: 4

Wireless Smart Gateway

Brand: Häfele Pages: 8

Brand: Planet Pages: 205

Content Security Gateway CS-500

Brand: Planet Pages: 215

Codian MSE 8321

Brand: TANDBERG Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands