manualshive.com logo in svg

IFM Electronic LK1022, Operating Instructions Manual, Page: 21 / 35

Share
Download
IFM Electronic LK1022 Operating Instructions Manual Download Page 21

21

UK

The unit can be programmed before or after installation. Exception: to 

adjust the overflow protection [cOP], the unit 

must

 be installed in the tank. 

10.2  Basic settings 

Setting ranges of all parameters: 

→ 12

Factory settings of all parameters: 

→ 14

10.2.1  Setting the unit of measurement [uni]

 

►

Enter [uni] before entering the values for SPx, rPx, OP or OFS. 

This avoids unintentional maladjustments.

 

►

Select [uni] 

 

►

Set the unit of measurement: [cm], [inch]

uni

10.2.2  Setting the offset [OFS]

The distance between tank bottom and lower edge of the measuring probe can be 

entered as offset value 

(→ 5.2.4)

. 

 

►

Set [OFS] before entering the values for SPx, rPx or OP. 

This avoids unintentional maladjustments.

 

►

Select [OFS]. 

 

►

Set the value for the offset. Note the set unit of measurement [uni].

OFS

10.2.3  Setting the medium [MEdI]

 

►

Select [MEdI] and set the corresponding sensitivity: 

MEdI

[CLW.1] = water, hydrous media, coolant emulsions.
[CLW.2] = water-based media for temperatures > 35 °C (installation in 

climatic tube).

[OIL.1] = oils with an increased DC value (e.g. some synthetic oils).
[OIL.2] = oils with a low DC value (e.g. mineral oils).
[Auto] =

automatic medium detection.

 

►

In case of doubt, select [OIL.2] for oils. 

 

►

Proper functioning is to be ensured by carrying out an application test!

Summary of Contents for LK1022




































Reviews:

No comments