IFM Electronic GM705S Original Operating Instructions Download | Manualshive

Page: 5 / 21

background image

5

UK

► Adhere to the principle of normally closed operation for all external safety

circuits connected to the system�

► In case of faults within the fail-safe sensor which result in the defined safe

state: take measures to maintain the safe state when the complete control

system continues to be operated�

► Replace damaged units�

3 Items supplied

1 fail-safe sensor GM705S with premounted angle bracket,

1 Allen key for fixing the fail-safe sensor onto the angle bracket,

1 operating instructions GM705S, ident number 704241�
If one of the above-mentioned components is missing or damaged, please contact

one of the ifm branch offices�

4 Functions and features

The fail-safe inductive sensor GM705S detects metal without contact�
Safety function SF: The safe state (output stage switched off; logic "0") is achieved

when undamping greater than or equal to the safe switch-off distance s

ar

(→ 11 Technical data)�

Also observe the notes on installation of the sensor (→ 6 Installation)�
The fail-safe sensor conforms to the category 4 according to EN 954-1 (valid until

31 December 2011), Performance Level e according to EN ISO 13849-1:2008 as

well as to the requirements SIL 3 to IEC 61508 and meets SILcl 3 to IEC 62061�
The unit corresponds to the classification I2C40SP2 to IEC 60947-5-2 for non-

flush installation (→ 6 Installation)�
The fail-safe inductive sensor has been certified by TÜVNord�

«
...
3
4
5
6
7
...
»

Summary of Contents for GM705S






















Reviews:

No comments

Related manuals for GM705S

Brand: Campbell Pages: 70

Brand: Yuasa Pages: 35

Brand: 3M Pages: 10

Brand: Pacbrake Pages: 9

Brand: Banner Pages: 10

DWSC - Vintage C

Brand: Daikin Pages: 57

Brand: e-conolight Pages: 3

Brand: E+E Elektronik Pages: 16

Brand: E+E Elektronik Pages: 14

Brand: E+E Elektronik Pages: 22

Brand: E+E Elektronik Pages: 16

Brand: E+E Elektronik Pages: 16

Brand: FeiYu Tech Pages: 34

EZ Link DAL 150

Brand: Harman Kardon Pages: 16

Brand: Salta Pages: 91

Brand: Kampmann Pages: 32

Brand: Prorack Pages: 15

Brand: PROAIM Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands