IFM Electronic GM705S Original Operating Instructions Download

Page: 19 / 21

12 Troubleshooting

(→ 9�4 LED display)

Problem

Possible cause

Troubleshooting

No LED display

No voltage supply

Apply voltage

Power LED flashes and

sensor does not switch

• Undervoltage

• Overvoltage

Correct the voltage

(→ 11 Technical data)

Sensor does not switch,

not even after undamping

and redamping

Sensor was brought into the

safe state (logic "0")� Cause:

• Cross fault between both

outputs A1 and A2

• Cross fault between one

output (A1 or A2) and the

supply voltage

• Error in the sensor detected

• Switch the operating voltage

off and on again

• Check wiring and connec-

tions

• Check external electronics

(e�g� PLC)

• Remove the cross fault

• Replace the unit

13 Maintenance, repair and disposal

If used correctly no maintenance and repair measures are necessary�

Only the manufacturer is allowed to repair the unit�

After use dispose of the unit in an environmentally friendly way in accordance with

the applicable national regulations�

Summary of Contents for GM705S






















Search results

Summary of Contents for GM705S

Reviews:

Related manuals for GM705S

Brands by name

Popular brands

IFM Electronic GM705S, Original Operating Instructions

Search results

Summary of Contents for GM705S

Reviews:

Related manuals for GM705S

Brands by name

Popular brands