IFM Electronic Efector 100 GM505S Operating Instructions Manual Download Page 2

Page: 2 / 21

Contents

1 Preliminary note ��3

1�1 Explanation of symbols ��3

2 Safety instructions ��4

2�1 Safety-related requirements regarding the application ��4

3  Items supplied��5
4  Functions and features ��5
5  Function ��6

5�1 Enable zone ��6

5�2 Protection against simple defeating ��7

6 Installation��8

6�1 Alignment of the sensing face ��8

6�2 Installation conditions ��9

7 Electrical connection ��9
8 Set-up ��10

8�1 Activate adjustment mode ��10

8�2 Determine the enable zone ��11

8�3 End adjustment mode ��11

9 Operation ��12

9�1 Sensor signals ��12

9�2 Input characteristics / output characteristics ��12

9�3 Cross faults ��13

9�4 Operating mode ��13

9�4�1 Delayed switching of the LED ��13

9�4�2 Switching of the LED without delay ��14

9�5 Response times ��15

9�6 LED display ��16

10  Scale drawing ��17
11  Technical data ��17
12  Troubleshooting ��20
13  Maintenance, repair and disposal ��20

Summary of Contents for Efector 100 GM505S






















Search results

Summary of Contents for Efector 100 GM505S

Reviews:

IFM Electronic Efector 100 GM505S, Operating Instructions Manual, Page: 2 / 21

Search results

Summary of Contents for Efector 100 GM505S

Reviews: