IFM Electronic Efector 100 GM505S Operating Instructions Manual Download Page 5 | Manualshive

Page: 5 / 21

IFM Electronic Efector 100 GM505S Operating Instructions Manual Download Page 5

5

UK

► Adhere to the principle of normally closed operation for all external safety

circuits connected to the system�

► In case of faults within the fail-safe sensor which result in the defined safe

state: take measures to maintain the safe state when the complete control

system continues to be operated�

► Replace damaged units�

3 Items supplied

1 fail-safe sensor GM505S with premounted angle bracket,

1 Allen key for fixing the fail-safe sensor onto the angle bracket,

1 operating instructions GM505S, ident number 701832�
If one of the above-mentioned components is missing or damaged, please contact

one of the ifm branch offices�

4 Functions and features

The fail-safe inductive sensor detects metal without contact�
Safety function SF: the safe state (output stage switched off; logic "0") is achieved

when undamping greater than or equal to the safe switch-off distance s

ar

Technical data)�

Also observe the notes on installation of the sensor (→ 6 Installation)�
The fail-safe sensor conforms to the category 4 according to EN 954-1 (valid until

31 December 2011), Performance Level e according to EN ISO 13849-1:2008 as

well as to the requirements SIL 3 to IEC 61508�
The unit corresponds to the classification I2C40SP2M to IEC 60947-5-2 for non-

flush installation (→ 6 Installation)�
The fail-safe inductive sensor has been certified by TÜVNord�

«
...
3
4
5
6
7
...
»

Summary of Contents for Efector 100 GM505S






















Reviews:

No comments