manualshive.com logo in svg

IFM Electronic Ax460, Operating Instructions Manual, Page: 5 / 36

Share
Download
IFM Electronic Ax460 Operating Instructions Manual Download Page 5

UK

Operating  instructions  AX460  

5

2  Safety instructions

2.1  General safety instructions

This description is an essential part of the device and contains important 

information concerning installation, function and operation� Non-compliance may 

result in damage or can affect the safety of operators and installations!
Using this device description requires appropriately qualified staff� The device may 

only be installed, configured, set up and maintained by a qualified and trained 

electrician�
Exclusion of liability: The manufacturer is not liable for any personal injuries or 

damage to property that may be caused by improper installation, set-up, operation 

and maintenance or by human misinterpretation or mistakes in this device 

description� Moreover, the manufacturer reserves the right to change technical 

aspects of the device or the description at any time; also without prior notice� 

Therefore, possible deviations between the device and the descriptions cannot be 

excluded�
The builder of the installation or the entire system is responsible for the safety of 

the installation or the entire system in which the system is to be integrated�
During installation, operation and maintenance works, all general and country-

specific as well as application-specific safety regulations and standards must be 

observed and respected�
If the device is used in processes where human error or operating errors may 

cause damage to the installation or injuries to persons, corresponding measures 

must be taken to ensure reliable prevention of such consequences�

3  Functions and features

This device must only be used in industrial machines and installations� Other uses 

do not comply with the regulations and are the sole responsibility of the user� 

The manufacturer is not liable for damage caused by improper use� The device 

must only be installed in compliance with the instructions and only be used and 

operated in a perfect technical condition that is in accordance with the technical 

data� The device is neither suited for explosion-protected areas nor for areas that 

are excluded in DIN EN 61010-1�

Summary of Contents for Ax460





































Reviews:

No comments