manualshive.com logo in svg

IFM Electronic Ax460, Operating Instructions Manual, Page: 21 / 36

Share
Download
IFM Electronic Ax460 Operating Instructions Manual Download Page 21

UK

Operating  instructions  AX460  

21

DECIMAL POINT

This setting defines the position of the decimal point�
NO

No decimal point

0000000�0

Decimal point at the specified spot

000000�00

Decimal point at the specified spot

00000�000

Decimal point at the specified spot

0000�0000

Decimal point at the specified spot

000�00000

Decimal point at the specified spot

00�000000

Decimal point at the specified spot

0�0000000

Decimal point at the specified spot

SCALE UNITS

Configuration of the indicated unit (→ 9.3 IN 1 Properties)

9.6  IN 2 Properties

In this menu the parameters for input 2 are defined�

CONFIGURATION

Configuration of input 2 (→ 9.3 IN 1 Properties)

START VALUE

Display value of input 2 for an input signal of 0 V, 0 mA or 4 mA (→ 9.3 IN 1 Properties) 

END VALUE

Display value of input 2 for an input signal of 10 V or 20 mA (→ 9.3 IN 1 Properties) 

DECIMAL POINT

Setting of the decimal point (→ 9.3 IN 1 Properties) 

SCALE UNITS

Unit indicated on the display (→ 9.3 IN 1 Properties) 

SAMPLING TIME (S)

Sampling interval of input 2 (→ 9.3 IN 1 Properties) 

AVERAGE FILTER

Optional averaging (→ 9.3 IN 1 Properties) 

OFFSET

Zero point shift / tare (→ 9.3 IN 1 Properties) 

LINEARIZATION

Linearisation function (→ 9.3 IN 1 Properties) 

TOTALIZATION

Totalisation function (→ 9.3 IN 1 Properties) 

Summary of Contents for Ax460





































Reviews:

No comments