manualshive.com logo in svg

IFM Electronic Ax460, Operating Instructions Manual, Page: 28 / 36

Share
Download
IFM Electronic Ax460 Operating Instructions Manual Download Page 28

Operating instructions AX460

28

OUTPUT TARGET 3

Assignment of an output for the switching condition of preselection 3  (→ 9.11 Preselection 1 Menu) (except 

default value)

see Preselection 1 Menu

CTRL OUT 3

Assignment of the switching condition to Ctrl� Out 3

OUTPUT POLARITY 3

Switching status for the switching condition of preselection 3, (→ 9.11 Preselection 1 Menu)

OUTPUT LOCK 3

Latching for the switching condition of preselection 3 (→ 9.11 Preselection 1 Menu)

START UP DELAY 3 (S)

Start-up delay for the switching condition of preselection 3� This setting only applies for the switching 

conditions |RESULT|<=|PRES| und RESULT<=PRES�
(Start-up delays 1 and 2 have a time-dependent start-up delay�)
OFF

No start-up delay

AUTO

Automatic start-up delay until the preselection value / switch point has 

been exceeded for the first time�

EVENT COLOR 3

Event-dependent colour change of the display for the switching condition of preselection 3, see 

Preselection 1 Menu

9.14  Preselection 4 Menu

SOURCE 4

Source for preselection 4 (→ 9.11 Preselection 1 Menu)

MODE 4

Switching condition for preselection 4, (→ 9.11 Preselection 1 Menu) (except tracking preset)

see Preselection 1 Menu

RES≥PRES-TRAIL

Tracking preset 4: 

Display value greater or equal to preselection 3 – preselection 4 

Preselection 4 is the tracking preset of preselection 3�

HYSTERESIS 4

Switching hysteresis for the switching condition of preselection 4, (→ 9.11 Preselection 1 Menu)

PULSE TIME 4 (S)

Duration of the fleeting pulse for the switching condition of preselection 4 (→ 9.11 Preselection 1 Menu)

Summary of Contents for Ax460





































Reviews:

No comments