IEI Technology PUZZLE-M801 User Manual Download Page 12

Page: 12 / 58

PUZZLE-M801

Page 4

1.5 Rear Panel

An overview of the PUZZLE-M801 rear panel is shown in

Figure 1-3

below.

Figure 1-3: PUZZLE-M801 Rear Panel

1.6 Technical Specifications

The PUZZLE-M801 technical specifications are listed below.

System

Form Factor

CPU (SoC)

Marvell

ARMADA

8040 processor (quad-core, 1.8 GHz)

Memory

One 288-pin 2400 MHz DDR4 ECC/non-ECC RDIMM slot

(system max. 16 GB)

(8G SKUs are pre-installed with one 8 GB memory module)

Networking

2 x 10GbE SFP+ port

4 x 1GbE LAN port via Marvell

ALASKA

88E1512P PHY

Network Acceleration

and Security

Configurable packet processor

HW offload for networking

Acceleration engines for storage, networking and security

Public Key Processor (RSA/DH/ECC)

Secure Storage

Secure boot

Summary of Contents for PUZZLE-M801



























































Search results

Summary of Contents for PUZZLE-M801

Reviews:

Related manuals for PUZZLE-M801

Brands by name

Popular brands

IEI Technology PUZZLE-M801, User Manual

Search results

Summary of Contents for PUZZLE-M801

Reviews:

Related manuals for PUZZLE-M801

Brands by name

Popular brands