IEI Technology PM-BT series User Manual Download Page 76

Page: 76 / 108

PM-BT SBC

Page 64



Console Redirection [Disabled]

Use

Console Redirection

option to enable or disable the console redirection function.



Disabled

EFAULT

Disabled the console redirection function



Enabled

Enabled the console redirection function

The following options are available in the

Console Redirection Settings

submenu when

the

Console Redirection

option is enabled.



Terminal Type [ANSI]

Use the

Terminal Type

option to specify the remote terminal type.



VT100

The target terminal type is VT100



VT100+

The target terminal type is VT100+



VT-UTF8

The target terminal type is VT-UTF8



ANSI

EFAULT

The target terminal type is ANSI



Bits per second [115200]

Use the

Bits per second

option to specify the serial port transmission speed. The speed

must match the other side. Long or noisy lines may require lower speeds.



9600

Sets the serial port transmission speed at 9600.



19200

Sets the serial port transmission speed at 19200.



38400

Sets the serial port transmission speed at 38400.



57600

Sets the serial port transmission speed at 57600.



115200

EFAULT

Sets the serial port transmission speed at 115200.



Data Bits [8]

Use the

Data Bits

option to specify the number of data bits.



Sets the data bits at 7.



EFAULT

Sets the data bits at 8.

Summary of Contents for PM-BT series













































































































Search results

Summary of Contents for PM-BT series

Reviews:

Related manuals for PM-BT series

Brands by name

Popular brands

IEI Technology PM-BT series, User Manual

Search results

Summary of Contents for PM-BT series

Reviews:

Related manuals for PM-BT series

Brands by name

Popular brands