IEI Technology PM-BT series User Manual Download Page 74

Page: 74 / 108

PM-BT SBC

Page 62

CPU_CORE

+5V

+12V

DDR

+5VSB

+3.3V

+3.3VSB

5.3.5 RTC Wake Settings

The

RTC Wake Settings

menu (

BIOS Menu 8

) configures RTC wake event.

Advanced

Wake system with Fixed Time

[Disabled]

Enable or disable System
wake on alarm event. When
enabled, System will
wake on the
date::hr::min::sec
specified

----------------------



: Select Screen

↑

↓

: Select Item

Enter

Select

General Help

Previous Values

Optimized Defaults

Save

ESC Exit

BIOS Menu 8: RTC Wake Settings



Wake system with Fixed Time [Disabled]

Use the

Wake system with Fixed Time

option to enable or disable the system wake on

alarm event.



Disabled

EFAULT

The real time clock (RTC) cannot generate a wake

event



Enabled

If selected, the

Wake up every day

option appears

Summary of Contents for PM-BT series













































































































Search results

Summary of Contents for PM-BT series

Reviews:

Related manuals for PM-BT series

Brands by name

Popular brands

IEI Technology PM-BT series, User Manual

Search results

Summary of Contents for PM-BT series

Reviews:

Related manuals for PM-BT series

Brands by name

Popular brands