IEI Technology PM-BT series User Manual Download Page 69

Page: 69 / 108

PM-BT SBC

Page 57

5.3.2 ACPI Settings

The

ACPI Settings

menu (

BIOS Menu 4

) configures the Advanced Configuration and

Power Interface (ACPI) options.

Advanced

ACPI Settings

ACPI Sleep State

[S3 (Suspend to RAM]

Select the highest ACPI
sleep state the system
will enter when the
SUSPEND button is
pressed.

----------------------



: Select Screen

↑

↓

: Select Item

Enter

Select

+/-: Change Opt.
F1:  General Help
F2:  Previous Values
F3:  Optimized Defaults
F4:  Save & Exit
ESC: Exit

BIOS Menu 4: ACPI Configuration



ACPI Sleep State [S3 only (Suspend to RAM)]

The fields in

ACPI Sleep State

option cannot be changed.



S3 (Suspend to

RAM)

EFAULT

The caches are flushed and the CPU is powered

off. Power to the RAM is maintained. The

computer returns slower to a working state, but

more power is saved.

Summary of Contents for PM-BT series













































































































Search results

Summary of Contents for PM-BT series

Reviews:

Related manuals for PM-BT series

Brands by name

Popular brands

IEI Technology PM-BT series, User Manual

Search results

Summary of Contents for PM-BT series

Reviews:

Related manuals for PM-BT series

Brands by name

Popular brands