manualshive.com logo in svg

IEI Technology NANO-QM871-i1, User Manual

Share
Download
IEI Technology NANO-QM871-i1 User Manual Download Page 83

 

 

NANO-QM871-i1 EPIC SBC

Page 70 

 

Figure 4-25: VGA Connector 

Step 4: 

Secure the connector

. Secure the DB-15 VGA connector from the VGA 

monitor to the external interface by tightening the two retention screws on either 

side of the connector.

 

Step 0:

 

4.11 Intel® AMT Setup Procedure 

The NANO-QM871-i1 is featured with the Intel® Active Management Technology (AMT). 

To enable the Intel® AMT function, follow the steps below.   

Step 1: 

Make sure the 

DIMM1

 socket is installed with one DDR3 SO-DIMM.   

Step 2: 

Connect an Ethernet cable to the RJ-45 connector labeled 

LAN1

. 

Step 3: 

The AMI BIOS options regarding the Intel® ME or Intel® AMT must be enabled.   

Step 4: 

Properly install the Intel® Management Engine Components drivers from the 

iAMT Driver & Utility directory in the driver CD. See 

Section 6.8

.  

Step 5: 

Configure the Intel® Management Engine BIOS extension (MEBx). To get into 

the Intel® MEBx settings, press <Ctrl+P> after a single beep during boot-up 

Summary of Contents for NANO-QM871-i1





























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands