IEI Technology NANO-QM871-i1 User Manual Download

Page: 68 / 156

NANO-QM871-i1 EPIC SBC

Page 55

Figure 4-10: Securing the Full-size PCIe Mini Card

4.7 System Configuration

The system configuration is controlled by buttons, jumpers and switches. The system

configuration should be performed before installation.

4.7.1 AT/ATX Mode Selection

Jumper Label:

J_ATXCTL1

Jumper Type:

Switch

Jumper Settings:

See

Figure 4-11

Jumper Location:

See

Figure 4-11

Set the switch to select AT or ATX power mode for the NANO-QM871-i1. AT power mode

limits the system to on/off. ATX allows the system to use various power saving states and

enter a standby state, so the system can be turned on remotely over a network. To

configure, see the diagram below.

Summary of Contents for NANO-QM871-i1





























































































































































Search results

Summary of Contents for NANO-QM871-i1

Reviews:

Related manuals for NANO-QM871-i1

Brands by name

Popular brands

IEI Technology NANO-QM871-i1, User Manual

Search results

Summary of Contents for NANO-QM871-i1

Reviews:

Related manuals for NANO-QM871-i1

Brands by name

Popular brands