IEI Technology NANO-QM871-i1-i7 User Manual Download Page 80

Page: 80 / 159

NANO-QM871-i1 EPIC SBC

Page 67

Figure 4-22: HDMI Connection

Step 3:

Insert the HDMI connector.

Gently insert the HDMI connector. The connector

should engage with a gentle push. If the connector does not insert easily, check

again that the connector is aligned correctly, and that the connector is being

inserted with the right way up.

Step 0:

4.10.2 LAN Connection

The RJ-45 connectors enable connection to an external network. To connect a LAN cable

with an RJ-45 connector, please follow the instructions below.

Step 1:

Locate the RJ-45 connectors

. The locations of the RJ-45 connectors are

shown in

Chapter 3

Step 2:

Align the connectors.

Align the RJ-45 connector on the LAN cable with one of

the RJ-45 connectors on the NANO-QM871-i1. See

Figure 4-23

Summary of Contents for NANO-QM871-i1-i7
































































































































































Search results

Summary of Contents for NANO-QM871-i1-i7

Reviews:

Related manuals for NANO-QM871-i1-i7

Brands by name

Popular brands

IEI Technology NANO-QM871-i1-i7, User Manual

Search results

Summary of Contents for NANO-QM871-i1-i7

Reviews:

Related manuals for NANO-QM871-i1-i7

Brands by name

Popular brands