IEI Technology NANO-QM871-i1-i7 User Manual Download Page 93

Page: 93 / 159

NANO-QM871-i1 EPIC SBC

Page 80

Wake system with Fixed Time [Disabled]

Use the

Wake system with Fixed Time

option to enable or disable the system wake on

alarm event.

Disabled D

EFAULT

The real time clock (RTC) cannot generate a wake

event

Enabled

If selected, the

Wake up every day

option appears

allowing you to enable to disable the system to wake

every day at the specified time. Besides, the

following options appear with values that can be

selected:

Wake up every day

Wake

date

Wake

hour

Wake up minute

Wake

second

After setting the alarm, the computer turns itself on

from a suspend state when the alarm goes off.

Summary of Contents for NANO-QM871-i1-i7
































































































































































Search results

Summary of Contents for NANO-QM871-i1-i7

Reviews:

Related manuals for NANO-QM871-i1-i7

Brands by name

Popular brands

IEI Technology NANO-QM871-i1-i7, User Manual

Search results

Summary of Contents for NANO-QM871-i1-i7

Reviews:

Related manuals for NANO-QM871-i1-i7

Brands by name

Popular brands