IEI Technology NANO-QM871-i1-i7 User Manual Download Page 108

Page: 108 / 159

NANO-QM871-i1 EPIC SBC

Page 95

Terminal Type [ANSI]

Use the

Terminal Type

option to specify the remote terminal type.

VT100

The target terminal type is VT100

VT100+

The target terminal type is VT100+

VT-UTF8

The target terminal type is VT-UTF8

ANSI D

EFAULT

The target terminal type is ANSI

Bits per second [115200]

Use the

Bits per second

option to specify the serial port transmission speed. The speed

must match the other side. Long or noisy lines may require lower speeds.

9600

Sets the serial port transmission speed at 9600.

19200

Sets the serial port transmission speed at 19200.

38400

Sets the serial port transmission speed at 38400.

57600

Sets the serial port transmission speed at 57600.

115200 D

EFAULT

Sets the serial port transmission speed at 115200.

Data Bits [8]

Use the

Data Bits

option to specify the number of data bits.

Sets the data bits at 7.

8 D

EFAULT

Sets the data bits at 8.

Parity [None]

Use the

Parity

option to specify the parity bit that can be sent with the data bits for

detecting the transmission errors.

None D

EFAULT

No parity bit is sent with the data bits.

Summary of Contents for NANO-QM871-i1-i7
































































































































































Search results

Summary of Contents for NANO-QM871-i1-i7

Reviews:

Related manuals for NANO-QM871-i1-i7

Brands by name

Popular brands

IEI Technology NANO-QM871-i1-i7, User Manual

Search results

Summary of Contents for NANO-QM871-i1-i7

Reviews:

Related manuals for NANO-QM871-i1-i7

Brands by name

Popular brands