IEI Technology Nano-PV-D4251 User Manual Download Page 74

Page: 74 / 153

NANO-PV-D4251/N4551/D5251 EPIC SBC

Page 61

Step 1:

Locate the DB-9 connector

. The location of the DB-9 connector is shown in

Chapter 3

Step 2:

Insert the serial connector

Insert the DB-9 connector of a serial device into

the DB-9 connector on the external peripheral interface. See Figure 4-18.

Figure 4-18: Serial Device Connector

Step 3:

Secure the connector

. Secure the serial device connector to the external

interface by tightening the two retention screws on either side of the connector.

4.8.4 USB Connection (Dual Connector)

The external USB Series "A" receptacle connectors provide easier and quicker access to

external USB devices. Follow the steps below to connect USB devices to the

NANO-PV-D4251/N4551/D5251.

Step 1:

Locate the USB Series "A" receptacle connectors

. The location of the USB

Series "A" receptacle connectors are shown in

Chapter 3

Summary of Contents for Nano-PV-D4251


























































































































































Search results

Summary of Contents for Nano-PV-D4251

Reviews:

Related manuals for Nano-PV-D4251

Brands by name

Popular brands

IEI Technology Nano-PV-D4251, User Manual

Search results

Summary of Contents for Nano-PV-D4251

Reviews:

Related manuals for Nano-PV-D4251

Brands by name

Popular brands