IEI Technology Nano-PV-D4251 User Manual Download Page 71

Page: 71 / 153

NANO-PV-D4251/N4551/D5251 EPIC SBC

Page 58

Figure 4-15: Single RS-232 Cable Installation

Step 3:

Secure the bracket

. The single RS-232 connector has two retention screws

that must be secured to a chassis or bracket.

Step 4:

Connect the serial device

. Once the single RS-232 connector is connected to

a chassis or bracket, a serial communications device can be connected to the

system.

4.8 External Peripheral Interface Connection

The following external peripheral devices can be connected to the external peripheral

interface connectors.

Keyboard and mouse

RJ-45 Ethernet cable connector

Serial

devices

USB

devices

VGA

monitor

To install these devices, connect the corresponding cable connector from the actual

device to the corresponding NANO-PV-D4251/N4551/D5251 external peripheral interface

connector making sure the pins are properly aligned.

Summary of Contents for Nano-PV-D4251


























































































































































Search results

Summary of Contents for Nano-PV-D4251

Reviews:

Related manuals for Nano-PV-D4251

Brands by name

Popular brands

IEI Technology Nano-PV-D4251, User Manual

Search results

Summary of Contents for Nano-PV-D4251

Reviews:

Related manuals for Nano-PV-D4251

Brands by name

Popular brands