IEI Technology Nano-PV-D4251 User Manual Download Page 23

Page: 23 / 153

NANO-PV-D4251/N4551/D5251 EPIC SBC

Page 10

2.1 Anti-static Precautions

WARNING!

Static electricity can destroy certain electronics. Make sure to follow the

ESD precautions to prevent damage to the product, and injury to the

user.

Make sure to adhere to the following guidelines:

Wear an anti-static wristband

: Wearing an anti-static wristband can prevent

electrostatic discharge.

Self-grounding

: Touch a grounded conductor every few minutes to discharge

any excess static buildup.

Use an anti-static pad

: When configuring any circuit board, place it on an

anti-static mat.

Only handle the edges of the PCB

: Don't touch the surface of the

motherboard. Hold the motherboard by the edges when handling.

2.2 Unpacking Precautions

When the NANO-PV-D4251/N4551/D5251 is unpacked, please do the following:

Follow the antistatic guidelines above.

Make sure the packing box is facing upwards when opening.

Make sure all the packing list items are present.

Summary of Contents for Nano-PV-D4251


























































































































































Search results

Summary of Contents for Nano-PV-D4251

Reviews:

Related manuals for Nano-PV-D4251

Brands by name

Popular brands

IEI Technology Nano-PV-D4251, User Manual

Search results

Summary of Contents for Nano-PV-D4251

Reviews:

Related manuals for Nano-PV-D4251

Brands by name

Popular brands