IEI Technology KINO-QM770 User Manual Download Page 89

Page: 89 / 208

KINO-QM770 Mini-ITX SBC

Page 73

4.9 External Peripheral Interface Connection

Devices can be connected to the external connectors. To install external devices, follow

the directions in the subsections below.

4.9.1 Audio Connector

The audio jacks on the external audio connector enable the KINO-QM770 to be connected

to a stereo sound setup. To install the audio devices, follow the steps below.

Step 1:

Identify the audio plugs

. The plugs on your home theater system or speakers

may not match the colors on the rear panel. If audio plugs are plugged into the

wrong jacks, sound quality will be very bad.

Step 2:

Plug the audio plugs into the audio jacks

. Plug the audio plugs into the audio

jacks. If the plugs on your speakers are different, an adapter will need to be used

to plug them into the audio jacks.

Line Out port (Lime):

Connects to a headphone or a speaker.

Microphone (Pink):

Connects to a microphone.

Figure 4-18: Audio Connector

Step 3:

Check audio clarity

. Check that the sound is coming through the right speakers

by adjusting the balance front to rear and left to right.

Step 0:

Summary of Contents for KINO-QM770

















































































































































































































Search results

Summary of Contents for KINO-QM770

Reviews:

Related manuals for KINO-QM770

Brands by name

Popular brands

IEI Technology KINO-QM770, User Manual

Search results

Summary of Contents for KINO-QM770

Reviews:

Related manuals for KINO-QM770

Brands by name

Popular brands