manualshive.com logo in svg

IEI Technology KINO-QM770, User Manual

Share
Download
IEI Technology KINO-QM770 User Manual Download Page 71

 

 

KINO-QM770 Mini-ITX SBC 

Page 55

4.3 CPU, CPU Cooling Kit and SO-DIMM Installation 

 WARNING: 

A CPU should never be turned on without the specified cooling kit 

being installed. If the cooling kit (heat sink and fan) is not properly 

installed and the system turned on, permanent damage to the CPU, 

KINO-QM770 and other electronic components attached to the system 

may be incurred. Running a CPU without a cooling kit may also result 

in injury to the user. 

The CPU, CPU cooling kit and DIMM are the most critical components of the 

KINO-QM770. If one of these component is not installed the KINO-QM770 cannot run. 

4.3.1 Socket G2 CPU Installation 

 WARNING: 

CPUs are expensive and sensitive components. When installing the 

CPU please be careful not to damage it in anyway. Make sure the CPU 

is installed properly and ensure the correct cooling kit is properly 

installed. 

To install a socket G2 CPU onto the KINO-QM770, follow the steps below: 

Summary of Contents for KINO-QM770

















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands