IEI Technology KINO-KX Series User Manual Download Page 75

Page: 75 / 110

KINO-KX SBC

Page 63

5.3.6 F81216 Sec. Super IO Configuration

Use the

F81216 Sec. Super IO Configuration

menu (

BIOS Menu 11

) to set or change

the configurations for the serial ports.

Advanced

F81216SEC Super IO Configuration

IRQ Share Mode

[PCI Share Mode]

Super IO Chip

F81216SEC

> Serial Port 7 Configuration
> Serial Port 8 Configuration
> Serial Port 9 Configuration
> Serial Port 10 Configuration

Select SEC SIO IRQ share
mode

---------------------



: Select Screen

↑

↓

: Select Item

Enter

Select

+/-: Change Opt.
F1: General Help
F2: Previous Values
F3:

Optimized

Defaults
F4:

Save & Exit

ESC: Exit

BIOS Menu 11: F81216 SEC Super IO Configuration



IRQ Share Mode [PCI Share Mode]

Use the

IRQ Share Mode

BIOS option to select the IRQ sharing mode of the second

super IO.



PCI Share Mode

EFAULT



ISA Share Mode

Summary of Contents for KINO-KX Series















































































































Search results

Summary of Contents for KINO-KX Series

Reviews:

Related manuals for KINO-KX Series

Brands by name

Popular brands

IEI Technology KINO-KX Series, User Manual

Search results

Summary of Contents for KINO-KX Series

Reviews:

Related manuals for KINO-KX Series

Brands by name

Popular brands