manualshive.com logo in svg

IEI Technology ITG-100-AL, User Manual

Share
Download
IEI Technology ITG-100-AL User Manual Download Page 40

 

 

ITG-100-AL Embedded System 

Page 28 

  WARNING: 

To mount the ITG-100-AL  embedded system  onto a DIN rail, please 

pay special attention to the direction of DIN  rail mounting kit.  See 

Figure 3-19 

3.11 RS-232/422/485 Serial Port Connection 

The ITG-100-AL has two RS-232/422/485 serial port connectors on the bottom panel. One 

is DB-9 connector and the other is RJ-45 connector.   

3.11.1 DB-9 RS-232/422/485 Serial Port Connection 

DB-9 RS-232/422/485 serial port devices can be attached to the DB-9 port on the bottom 

panel. 

Step 1: 

Locate the DB-9 connector

. The locations of the DB-9 connector are shown in 

Figure 1-3

. 

Step 2: 

Insert the serial connector

.

 

Insert the DB-9 connector of a serial device into 

the DB-9 connector on the external peripheral interface. See 

Figure 3-20

. 

 

Figure 3-20: Serial Device Connector 

Summary of Contents for ITG-100-AL












































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands