manualshive.com logo in svg

IEI Technology ISDM-084G, User Manual

Share
Download
IEI Technology ISDM-084G User Manual Download Page 92

 

 

ISDM Series Industrial Monitor

Page 92 

5.1 Installation Precautions 

When installing the ISDM series industrial monitor, please follow the precautions listed 

below: 

„

 

Read the user manual

: The user manual provides a complete description of 

the ISDM series industrial monitor, installation instructions and configuration 

options. 

„

 

DANGER! Disconnect Power

: Power to the monitor must be disconnected 

when installing the ISDM series industrial monitor, or before any attempt is 

made to access the rear panel. Electric shock and personal injury might occur 

if the rear panel of the monitor is opened while the power cord is still 

connected to an electrical outlet. 

„

 

Qualified Personnel

: The ISDM series industrial monitor must be installed 

and operated only by trained and qualified personnel. Maintenance, upgrades, 

or repairs may only be carried out by qualified personnel who are familiar with 

the associated dangers. 

„

 

Mounting

: Since the monitor may weigh up to 10 kg (not including a swing 

arm or other accessories), please ensure at least two people assist with 

mounting the monitor. 

„

 

Air Circulation

: Make sure there is sufficient air circulation when installing the 

monitor. The monitor’s cooling vents must not be obstructed by any objects. 

Blocking the vents can cause overheating of the monitor. Leave at least 5 cm 

of clearance around the monitor to prevent overheating. 

„

 

Grounding

: The monitor should be properly grounded. The voltage feeds 

must not be overloaded. Adjust the cabling and provide external overcharge 

protection per the electrical values indicated on the label attached to the back 

of the monitor. 

„

 

Anti-static Discharge

: The rear panel of the monitor must to be removed to 

configure the monitor’s AD board voltage select jumper. When doing so, be 

sure the monitor is disconnected from its power source and take all necessary 

safety precautions to avoid electrocution and static discharge to the AD board. 

The use of a grounded wrist strap and an anti-static work pad is 

recommended. 

Summary of Contents for ISDM-084G

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands