manualshive.com logo in svg

IEI Technology ISDM-084G, User Manual

Share
Download
IEI Technology ISDM-084G User Manual Download Page 136

 

 

ISDM Series Industrial Monitor

Page 136 

C.1 IEI smartOSD Quick Installation Guide 

IEI smartOSD is a proprietary On-Screen-Display (OSD) software solution from IEI that 

enables easy, remote monitor setting adjustments in a Windows environment. IEI 

smartOSD delivers excellent performance and provides more flexibility than the typical 

OSD hardware solutions when adjusting a monitor. smartOSD also allows monitor 

settings such as brightness, contrast, screen position, size, color gain to be read and 

changed over normal video cable (VGA or DVI). The smartOSD function is only supported 

by revision 1.1 models and above. 

C.2 Pre-installation Notice 

Before installing smartOSD software, please make sure one of the following operating 

systems is installed:   

„

 

Windows 95 

„

 

Windows NT 4.0 

„

 

Windows 98 

„

 

Windows 2000 

„

 

Windows 2003 

„

 

Windows XP 

„

 

Windows Vista 

C.3 smartOSD Install 

Connect the ISDM Series to a host computer. Insert the CD that came with the system and 

follow the instructions below. 

Step 1: 

When the CD install the screen shown in 

Figure 7-11

 appears. 

Summary of Contents for ISDM-084G

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands