manualshive.com logo in svg

IEI Technology ISDM-084G, User Manual

Share
Download
IEI Technology ISDM-084G User Manual Download Page 6

 

 

ISDM Series Industrial Monitor

Page 6 

Packing List 

 

NOTE: 

If any of the components listed in the checklist below are missing, 

please do not proceed with the installation. Contact the IEI reseller or 

vendor you purchased the ISDM Series from or contact an IEI sales 

representative directly. To contact an IEI sales representative, please 

send an email to [email protected]. 

The items listed below should all be included in the ISDM Series package. 

„

 

1 x ISDM-190/170/150/121/104/84 series industrial monitor. 

„

 

1 x AC Power cable 

„

 

1 x VGA Cable 

„

 

1 x 45W AC Power Adapter (ISDM-190 / 170 / 150 / 121) 

„

 

1 x 25W AC Power Adapter (ISDM-104 / 84) 

„

 

5 x Replacement Round Head Screw 

„

 

5 x Replacement Flat Head Screw 

„

 

5 x Replacement Wire Strain Band 

„

 

1 x User Manual on CDROM 

„

 

1 x Power Cable for Terminal Block (Optional for M model) 

„

 

1 x Touch Panel RS-232 Cable / Touch Pen / Driver CDROM (for T-R model) 

„

 

1 x Touch Panel USB Cable / Touch Pen / Driver CDROM (for USB/T-R 

model) 

Images of the above items are shown in 

Chapter 5

. 

Summary of Contents for ISDM-084G

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands