IEI Technology IMBA-H110 User Manual Download Page 76

Page: 76 / 152

IMBA-H110 ATX Motherboard

Page 62

Step 9:

Connect the 12 V power to the board.

Connect the 12 V power from the power

supply to the board.

Step 0:

4.4 Socket LGA1151 Cooling Kit Installation

WARNING:

DO NOT attempt to install a push-pin cooling fan.

The pre-installed support bracket prevents the board from
bending and is ONLY compatible with captive screw type cooling
fans.

The cooling kit can be bought from IEI. The cooling kit has a heat sink and fan.

WARNING:

Do not wipe off (accidentally or otherwise) the pre-sprayed layer of
thermal paste on the bottom of the heat sink. The thermal paste
between the CPU and the heat sink is important for optimum heat
dissipation.

To install the cooling kit, follow the instructions below.

Step 1:

A cooling kit bracket is pre-installed on the rear of the motherboard. See

Figure 4-5.

Summary of Contents for IMBA-H110

























































































































































Search results

Summary of Contents for IMBA-H110

Reviews:

Brands by name

Popular brands

IEI Technology IMBA-H110, User Manual

Search results

Summary of Contents for IMBA-H110

Reviews:

Brands by name

Popular brands