IEI Technology IMBA-H110 User Manual Download Page 77

Page: 77 / 152

IMBA-H110 ATX Motherboard

Page 63

Figure 4-5: Cooling Kit Support Bracket

Step 2:

Place the cooling kit onto the socket LGA1151 CPU

. Make sure the CPU

cable can be properly routed when the cooling kit is installed.

Step 3:

Mount the cooling kit

. Gently place the cooling kit on top of the CPU. Make

sure the four threaded screws on the corners of the cooling kit properly pass

through the holes of the cooling kit bracket.

Step 4:

Tighten the screws

. Use a screwdriver to tighten the four screws. In a diagonal

pattern, tighten each screw a few turns then move to the next one, until they are

all secured. Do not overtighten the screws.

Step 5:

Connect the fan cable

. Connect the cooling kit fan cable to the CPU fan

connector on the IMBA-H110. Carefully route the cable and avoid heat

generating chips and fan blades.

Step 0:

Summary of Contents for IMBA-H110

























































































































































Search results

Summary of Contents for IMBA-H110

Reviews:

Brands by name

Popular brands

IEI Technology IMBA-H110, User Manual

Search results

Summary of Contents for IMBA-H110

Reviews:

Brands by name

Popular brands