IEI Technology IMBA-H110 User Manual Download Page 114

Page: 114 / 152

IMBA-H110 ATX Motherboard

Page 100



Intel Virtualization Technology [Disabled]

Use the

Intel Virtualization Technology

option to enable or disable virtualization on the

system. When combined with third party software, Intel® Virtualization technology allows
several OSs to run on the same system at the same time.



Disabled

EFAULT

Disables Intel Virtualization Technology.



Enabled

Enables Intel Virtualization Technology.



Intel(R) SpeedStep(tm) [Enabled]

Use the

Intel(R) SpeedStep(tm)

option to enable or disable the Intel® SpeedStep

Technology which allows more than two frequency ranges to be supported.



Disabled

Disables Intel® SpeedStep Technology



Enabled

EFAULT

Enables Intel® SpeedStep Technology



CPU C states [Disabled]

Use the

CPU C states

option to enable or disable the CPU C states.



Disabled

EFAULT

Disables the CPU C states.



Enabled

Enables the CPU C states.



Intel TXT(LT) Support [Disabled]

Use the

Intel TXT(LT) Support

option to enable or disable the Intel(R) TXT(LT) support.



Disabled

EFAULT

Disables Intel® TXT(LT) support



Enabled

Enables Intel® TXT(LT) support

Summary of Contents for IMBA-H110

























































































































































Search results

Summary of Contents for IMBA-H110

Reviews:

Brands by name

Popular brands

IEI Technology IMBA-H110, User Manual

Search results

Summary of Contents for IMBA-H110

Reviews:

Brands by name

Popular brands