IEI Technology IceCare-10W series User Manual Download Page 23

Page: 23 / 107

ICECARE-10W Mobile Sales Assistant

Page 11

2.1 Unpack the System

To unpack the ICECARE-10W Series, follow the steps below:

WARNING!

Only remove the protective plastic cover stuck to the front screen after

installation. The plastic layer protects the monitor surface during

installation process.

Step 1:

Carefully cut the tape sealing the box. Only cut deep enough to break the tape.

Step 2:

Open the box.

Step 3:

Lift the ICECARE-10W Series out of the boxes.

Step 4:

Remove the peripheral parts box from the main box.

2.2 Packing List

NOTE:

If any of the components listed in the checklist below are missing, do

not proceed with the installation. Contact the IEI reseller or vendor the

ICECARE-10W Series was purchased from or contact an IEI sales

representative directly by sending an email to

[email protected]

The ICECARE-10W Series is shipped with the following components:

Summary of Contents for IceCare-10W series












































































































Search results

Summary of Contents for IceCare-10W series

Reviews:

Related manuals for IceCare-10W series

Brands by name

Popular brands

IEI Technology IceCare-10W series, User Manual

Search results

Summary of Contents for IceCare-10W series

Reviews:

Related manuals for IceCare-10W series

Brands by name

Popular brands